Difficulty

Moderate

Steps

13

Time Required

                          15 - 30 minutes            

Sections

5

  • Outer Case
  • 2 steps
  • Power Switch
  • 2 steps
  • Eject Button
  • 2 steps
  • Controller Port
  • 2 steps
  • Motherboard
  • 5 steps

Flags

0

  • BackSuper Nintendo

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Outer Case               
  • Remove the six screws located on the underside of the system using the Gamebit 4.5mm screwdriver.

Remove the six screws located on the underside of the system using the Gamebit 4.5mm screwdriver.

1024

Step 2

  • Carefully flip the unit back over.
  • Locate the seam. Lift and separate the upper half of the case from the lower half of the case.

Carefully flip the unit back over.

Locate the seam. Lift and separate the upper half of the case from the lower half of the case.

Step 3

              Power Switch               
  • Remove the two 11.7 mm Phillips #2 screws connecting the power switch to the motherboard.

Remove the two 11.7 mm Phillips #2 screws connecting the power switch to the motherboard.

Step 4

  • The power switch is connected to the motherboard near the top left of the console.
  • Carefully pull the connector from its socket on the motherboard. You may need to wiggle it out as you pull.
  • Do not detach the connector by pulling on the wires. This could damage the wires or the socket.

The power switch is connected to the motherboard near the top left of the console.

Carefully pull the connector from its socket on the motherboard. You may need to wiggle it out as you pull.

Do not detach the connector by pulling on the wires. This could damage the wires or the socket.

Step 5

              Eject Button               
  • Lift the right side of the eject lever out of the housing.

Lift the right side of the eject lever out of the housing.

Step 6

  • Pull the metal bar out through the right side of the eject lever.
  • Make sure to keep track of the spring located on the left side of the lever as it may shoot off when removing the metal bar.
  • When reassembling, the procedure becomes more difficult due to the spring (marked red). We recommend that one person hold the spring in place (picture 3) while another person slides the metal bar back into the left housing, and slide the eject lever onto the metal bar.

Pull the metal bar out through the right side of the eject lever.

Make sure to keep track of the spring located on the left side of the lever as it may shoot off when removing the metal bar.

When reassembling, the procedure becomes more difficult due to the spring (marked red). We recommend that one person hold the spring in place (picture 3) while another person slides the metal bar back into the left housing, and slide the eject lever onto the metal bar.

Step 7

              Controller Port               
  • Lift the controller ports out of the housing, this should be done without much force. Take note of the location of the ribbon cable connection.

Lift the controller ports out of the housing, this should be done without much force. Take note of the location of the ribbon cable connection.

Step 8

  • Carefully remove the ribbon cable from its port.

Carefully remove the ribbon cable from its port.

Step 9

              Motherboard               
  • Remove the two Phillips two 11.6mm screws that connect the front shield to the motherboard.

Remove the two Phillips two 11.6mm screws that connect the front shield to the motherboard.

Step 10

  • Lift the front shield straight up to remove it from the motherboard.

Lift the front shield straight up to remove it from the motherboard.

Step 11

  • Remove the two silver 15.6 mm Phillips #2 screws on either side of the 62 pin connector.

Remove the two silver 15.6 mm Phillips #2 screws on either side of the 62 pin connector.

Step 12

  • Remove the 11.8 mm Phillips #2 screw near the rear of the SNES.

Remove the 11.8 mm Phillips #2 screw near the rear of the SNES.

Step 13

  • Lift the motherboard straight up to remove it.

Lift the motherboard straight up to remove it.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      44 other people completed this guide.                                             

Author

                                      with 8 other contributors 

                    Melina                     

Member since: 10/12/2010

950 Reputation

                                      1 Guide authored                  



                       Badges:
                       11







                                                        +8 more badges                           

Team

                       Cal Poly, Team 4-47, Amido Fall 2010                        

                                                  Member of Cal Poly, Team 4-47, Amido Fall 2010 



                    CPSU-AMIDO-F10S4G47                     


                                            4 Members                     


                                            20 Guides authored                     

joshenders - Mar 3, 2016

Reply

There are several versions of the Super Nintendo. Steps for my version are a bit different.

Anonymous Idea - Jan 20, 2018

This seems to be a newer super nintendo. If you have one of the older ones, there will be a bit more screws but still basically the same steps.

Gena FM - Sep 24, 2022

There are two versions of the Super Nintendo- the one pictured here, and one with a sound chip board behind the game cartridge reader. These two models have different shells that are not interchangeable (important to know if you’re looking to buy a replacement housing for your SNES)

Rupin Soland - Jun 9, 2018

Reply

It’s possible they may be referring to the European/Japanese version of the Super Nintendo/Super Famicom. Either that, or it’s one of the weird, misshapen “reskins”.