Difficulty

Moderate

Steps

13

Time Required

                          20 - 40 minutes

Sections

4

  • How to Open the SteelSeries Stratus Duo
  • 7 steps
  • Thumbsticks
  • 2 steps
  • Mainboard Assembly
  • 2 steps
  • Trigger Button Covers
  • 2 steps

Flags

0

  • BackSteelSeries Stratus Duo

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove the sticker
  • Use your fingers to remove the sticker located on the back cover of the Stratus Duo.
  • If you have trouble removing the sticker, heat an iOpener and apply it to the rear case for two minutes to loosen the adhesive underneath. You can also use a hair dryer to soften the adhesive.

Use your fingers to remove the sticker located on the back cover of the Stratus Duo.

If you have trouble removing the sticker, heat an iOpener and apply it to the rear case for two minutes to loosen the adhesive underneath. You can also use a hair dryer to soften the adhesive.

1024

Step 2

              Unscrew the back cover
  • Use a Y0 Tri-point screwdriver to remove the five 9.3 mm-long screws securing the back cover.

Use a Y0 Tri-point screwdriver to remove the five 9.3 mm-long screws securing the back cover.

Step 3

              Reposition the back cover assembly
  • Don’t try to remove the back cover assembly all the way yet, as it’s still connected to the mainboard.
  • Carefully lift the back cover assembly away from the frame and move it downward to uncover the battery cable and the interconnect cable at the top of the motherboard.

Don’t try to remove the back cover assembly all the way yet, as it’s still connected to the mainboard.

Carefully lift the back cover assembly away from the frame and move it downward to uncover the battery cable and the interconnect cable at the top of the motherboard.

Step 4

              Disconnect the interconnect cable
  • Using the pointed end of a spudger, push the grey tabs on the interconnect socket away from the socket, parallel to the interconnect cable, to release the cable.

Using the pointed end of a spudger, push the grey tabs on the interconnect socket away from the socket, parallel to the interconnect cable, to release the cable.

Step 5

  • Use a pair of blunt nosed tweezers or your fingers to pull the cable out of the socket.

Use a pair of blunt nosed tweezers or your fingers to pull the cable out of the socket.

Step 6

              Disconnect the battery cable
  • Use a pair of blunt nose tweezers to grab and lift the connector away from the motherboard.

Use a pair of blunt nose tweezers to grab and lift the connector away from the motherboard.

Step 7

              Remove the back cover assembly
  • Remove the back cover assembly.

Remove the back cover assembly.

Step 8

              Unscrew the thumbsticks board
  • Use a Phillips screwdriver to remove the two 6.8 mm-long screws securing the thumbsticks board.

Use a Phillips screwdriver to remove the two 6.8 mm-long screws securing the thumbsticks board.

Step 9

              Disconnect the thumbsticks board
  • Grab the thumbsticks board with your hand and disconnect it by pulling it straight up and out of its socket on the mainboard.
  • Remove the thumbsticks board.
  • For reassembly make sure to correctly align the ten pins with their socket on the mainboard.

Grab the thumbsticks board with your hand and disconnect it by pulling it straight up and out of its socket on the mainboard.

Remove the thumbsticks board.

For reassembly make sure to correctly align the ten pins with their socket on the mainboard.

Step 10

              Unscrew the mainboard assembly
  • Use a Phillips screwdriver to remove the four 6.8 mm-long screws securing the mainboard assembly to the case.

Use a Phillips screwdriver to remove the four 6.8 mm-long screws securing the mainboard assembly to the case.

Step 11

              Remove the mainboard assembly
  • Use your hand to remove the mainboard assembly by tilting it out of the plastic cover.

Use your hand to remove the mainboard assembly by tilting it out of the plastic cover.

Step 12

              Unscrew the trigger button covers
  • Use a Phillips screwdriver to remove the four 7.2 mm-long screws securing the trigger button covers to the mainboard.

Use a Phillips screwdriver to remove the four 7.2 mm-long screws securing the trigger button covers to the mainboard.

Step 13

              Remove the trigger button covers
  • Use your fingers to pull the trigger button covers off of their shoulder button breakout boards.

Use your fingers to pull the trigger button covers off of their shoulder button breakout boards.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor 


                    Adriana Zwink

Member since: 12/18/2019

36,607 Reputation

                                      167 Guides authored                  



                       Badges:
                       34







                                                        +31 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored