Difficulty

Moderate

Steps

11

Time Required

                          10 minutes            

Sections

2

  • Cover
  • 7 steps
  • Power Cord
  • 4 steps

Flags

0

  • BackStaples 34462 Electric Pencil Sharpener

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Cover               
  • Pull out the shavings tray from the pencil sharpener.
  • Beware of loose pencil shavings falling on your workspace.

Pull out the shavings tray from the pencil sharpener.

Beware of loose pencil shavings falling on your workspace.

1024

Step 2

  • Turn the pencil sharpener on its side.

Turn the pencil sharpener on its side.

Step 3

  • Using a Phillips00 screwdriver, remove the two front 11.6mm screws.
  • Using the plastic opening tool, remove the back plastic feet.
  • After removing the back plastic feet, using a Phillips 00 screwdriver, remove the two back 11.6mm screws.
  • The hole is deeper than you may think. It may take some time to get the screwdriver to click in.

Using a Phillips00 screwdriver, remove the two front 11.6mm screws.

Using the plastic opening tool, remove the back plastic feet.

After removing the back plastic feet, using a Phillips 00 screwdriver, remove the two back 11.6mm screws.

The hole is deeper than you may think. It may take some time to get the screwdriver to click in.

Step 4

  • Carefully pull apart the bottom panel from the top panel.
  • Be careful not to pull too forcefully as the panels are connected by wires.
  • Beware of pencil shavings falling out onto your workspace.

Carefully pull apart the bottom panel from the top panel.

Be careful not to pull too forcefully as the panels are connected by wires.

Beware of pencil shavings falling out onto your workspace.

Step 5

  • Using a Phillips00 screwdriver, remove two 8.9mm flat edge screws from the top section of the top panel.

Using a Phillips00 screwdriver, remove two 8.9mm flat edge screws from the top section of the top panel.

Step 6

  • Using a Phillips00 screwdriver, remove two 10.3mm screws from the middle section of the top panel.

Using a Phillips00 screwdriver, remove two 10.3mm screws from the middle section of the top panel.

Step 7

  • Carefully pull the cover from the top panel and set it aside.

Carefully pull the cover from the top panel and set it aside.

Step 8

              Power Cord               
  • Orient the panel with the power cord so that it is facing you.
  • Using a Phillips00 screwdriver, remove the two flat head 8.95mm screws securing the cord.

Orient the panel with the power cord so that it is facing you.

Using a Phillips00 screwdriver, remove the two flat head 8.95mm screws securing the cord.

Step 9

  • Using a Phillips00 screwdriver, remove the two 10.42mm screws on the plastic frame securing the power component.

Using a Phillips00 screwdriver, remove the two 10.42mm screws on the plastic frame securing the power component.

Step 10

  • Carefully lift out the power component from the panel.

Carefully lift out the power component from the panel.

Step 11

  • Use a utility knife to cut the black insulation tape from the wire.
  • Cut the power cord from the wires to remove it.

Use a utility knife to cut the black insulation tape from the wire.

Cut the power cord from the wires to remove it.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    Jen Hawkins                     

Member since: 10/27/2014

449 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges                           

Team

                       Eastern Washington University, Team 1-5, Carnegie Fall 2014                        

                                                  Member of Eastern Washington University, Team 1-5, Carnegie Fall 2014 



                    EWU-CARNEGIE-F14S1G5                     


                                            7 Members                     


                                            6 Guides authored