Difficulty
Easy
Steps
14
Time Required
7 minutes
Sections
3
- Plastic Wing Replacement
- 3 steps
- Fur Replacement
- 8 steps
- Speaker Replacement
- 3 steps
Flags
0
BackSpin Master Hatchimal Draggle
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Plastic Wing Replacement
- lay the Hatchimal on its side.
lay the Hatchimal on its side.
1024
Step 2
- Using the plastic opening tool, push in on the purple clip.
Using the plastic opening tool, push in on the purple clip.
Step 3
- Pull the wing off of the hatchimal.
- The wing should come off with little resistance.
Pull the wing off of the hatchimal.
The wing should come off with little resistance.
Step 4
Fur Replacement
- Cut the fur retaining zip-tie with a pair of scissors.
Cut the fur retaining zip-tie with a pair of scissors.
Step 5
- Lift the fur up until it can’t go further.
Lift the fur up until it can’t go further.
Step 6
- Use the spudger tool to push up on the black clip to free it.
- Pull the clip out.
Use the spudger tool to push up on the black clip to free it.
Pull the clip out.
Step 7
- Lift fur up to reveal the next set of clips.
- Insert a spudger to push up on the black clip to free it.
- Pull out the clip.
Lift fur up to reveal the next set of clips.
Insert a spudger to push up on the black clip to free it.
Pull out the clip.
Step 8
- Lift the fur up and over the Hatchimals Head.
- Remove the six 12mm Phillips #00 screws from then body.
Lift the fur up and over the Hatchimals Head.
Remove the six 12mm Phillips #00 screws from then body.
Step 9
- Pull the casing apart.
- Remove the yellow speaker cable.
Pull the casing apart.
Remove the yellow speaker cable.
Step 10
- Remove the three 7mm Phillips #00 screws from the head.
- Remove the wheel base and the circuit board carefully not to damage the spring.
Remove the three 7mm Phillips #00 screws from the head.
Remove the wheel base and the circuit board carefully not to damage the spring.
Step 11
- Push the six black fur clips out using the spudger.
- Remove the fur completely.
Push the six black fur clips out using the spudger.
Remove the fur completely.
Step 12
Speaker Replacement
- Gently pull the yellow speaker cord from circuit board. There will be little resistance.
Gently pull the yellow speaker cord from circuit board. There will be little resistance.
Step 13
- Remove the two 7mm Philips #00 screws from the head.
Remove the two 7mm Philips #00 screws from the head.
Step 14
- Pull the speaker cover off.
- Remove the speaker.
Pull the speaker cover off.
Remove the speaker.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Hector Lopez
Member since: 02/14/2018
251 Reputation
2 Guides authored
Badges:
4
+1 more badge
Team
USF Tampa, Team S1-G5, Nance Spring 2018
Member of USF Tampa, Team S1-G5, Nance Spring 2018
USFT-NANCE-S18S1G5
3 Members
5 Guides authored
Jeff - Oct 11, 2018
Reply
Where can I get a new speaker?
kewrock - Jan 21, 2020
Reply
Same question . Where to get a matching speaker. Ebay is full of similar 23mm speakers. But which one to get? My Hatchimal speaker says 25w. I find it hard to believe it is 25 watts. The ones on ebay are 1 watt, 2 watt or half watt.