Difficulty

Moderate

Steps

14

Time Required

                          5 minutes

Sections

3

  • Plastic Wing Replacement
  • 3 steps
  • Fur Replacement
  • 8 steps
  • Nose Spring Replacement
  • 3 steps

Flags

0

  • BackSpin Master Hatchimal Draggle

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Plastic Wing Replacement
  • lay the Hatchimal on its side.

lay the Hatchimal on its side.

1024

Step 2

  • Using the plastic opening tool, push in on the purple clip.

Using the plastic opening tool, push in on the purple clip.

Step 3

  • Pull the wing off of the hatchimal.
  • The wing should come off with little resistance.

Pull the wing off of the hatchimal.

The wing should come off with little resistance.

Step 4

              Fur Replacement
  • Cut the fur retaining zip-tie with a pair of scissors.

Cut the fur retaining zip-tie with a pair of scissors.

Step 5

  • Lift the fur up until it can’t go further.

Lift the fur up until it can’t go further.

Step 6

  • Use the spudger tool to push up on the black clip to free it.
  • Pull the clip out.

Use the spudger tool to push up on the black clip to free it.

Pull the clip out.

Step 7

  • Lift fur up to reveal the next set of clips.
  • Insert a spudger to push up on the black clip to free it.
  • Pull out the clip.

Lift fur up to reveal the next set of clips.

Insert a spudger to push up on the black clip to free it.

Pull out the clip.

Step 8

  • Lift the fur up and over the Hatchimals Head.
  • Remove the six 12mm Phillips #00 screws from then body.

Lift the fur up and over the Hatchimals Head.

Remove the six 12mm Phillips #00 screws from then body.

Step 9

  • Pull the casing apart.
  • Remove the yellow speaker cable.

Pull the casing apart.

Remove the yellow speaker cable.

Step 10

  • Remove the three 7mm Phillips #00 screws from the head.
  • Remove the wheel base and the circuit board carefully not to damage the spring.

Remove the three 7mm Phillips #00 screws from the head.

Remove the wheel base and the circuit board carefully not to damage the spring.

Step 11

  • Push the six black fur clips out using the spudger.
  • Remove the fur completely.

Push the six black fur clips out using the spudger.

Remove the fur completely.

Step 12

              Nose Spring Replacement
  • Using the angled tweezers tool, disconnect the spring that is attached to the nose from the lever.

Using the angled tweezers tool, disconnect the spring that is attached to the nose from the lever.

Step 13

  • Separate the body casing from the core and circuit board.
  • Don’t damage the small wire connected from the top of the head to the circuit board.

Separate the body casing from the core and circuit board.

Don’t damage the small wire connected from the top of the head to the circuit board.

Step 14

  • Remove a single 7mm Phillips #00 screw from the break.
  • Remove the spring.

Remove a single 7mm Phillips #00 screw from the break.

Remove the spring.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Hector Lopez

Member since: 02/14/2018

251 Reputation

                                      2 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       USF Tampa, Team S1-G5, Nance Spring 2018                        

                                                  Member of USF Tampa, Team S1-G5, Nance Spring 2018 



                    USFT-NANCE-S18S1G5                     


                                            3 Members                     


                                            5 Guides authored