Difficulty
Moderate
Steps
10
Time Required
8 minutes
Sections
2
- Robot Screen
- 5 steps
- Robot Wheel Gears
- 5 steps
Flags
0
BackSpin Master Boxer
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Robot Screen
- Set Spin Master Boxer on your workspace so that the bottom panel faces upwards.
Set Spin Master Boxer on your workspace so that the bottom panel faces upwards.
1024
Step 2
- Using a Phillips #00 screw driver, unscrew the four 4mm screws in each corner of the bottom panel.
Using a Phillips #00 screw driver, unscrew the four 4mm screws in each corner of the bottom panel.
Step 3
- Carefully remove the bottom panel of the Spin Master Boxer by lifting up, away from the main body of robot.
Carefully remove the bottom panel of the Spin Master Boxer by lifting up, away from the main body of robot.
Step 4
- While holding onto the axels of the wheels, gently pull the top panel of the robot away from its body.
- Be aware when removing the panel that multiple wires connect it to the body of the Spin Master Boxer.
While holding onto the axels of the wheels, gently pull the top panel of the robot away from its body.
Be aware when removing the panel that multiple wires connect it to the body of the Spin Master Boxer.
Step 5
- Remove the plastic screen from the body of the robot. It should come off easily as it is not attached by anything.
Remove the plastic screen from the body of the robot. It should come off easily as it is not attached by anything.
Step 6
Robot Wheel Gears
- Place robot on back so that the sensors are facing up.
Place robot on back so that the sensors are facing up.
Step 7
- Gently separate the left set of wheels from the inner portion of the circuit board, by gripping the wheels and pulling them away from main body of robot.
- There are wires attached to each set of wheels, so be careful not to rip them apart.
- Repeat the process for the right set of wheels.
Gently separate the left set of wheels from the inner portion of the circuit board, by gripping the wheels and pulling them away from main body of robot.
There are wires attached to each set of wheels, so be careful not to rip them apart.
Repeat the process for the right set of wheels.
Step 8
- Use the Phillips #00 Screwdriver to remove the 3mm screw that connect the black wheels to the gears.
- You will have to go through the black wheel to unscrew some of the screws.
Use the Phillips #00 Screwdriver to remove the 3mm screw that connect the black wheels to the gears.
You will have to go through the black wheel to unscrew some of the screws.
Step 9
- Grip wheel, and gently pull up, to separate white gear casing into its front and back panel.
Grip wheel, and gently pull up, to separate white gear casing into its front and back panel.
Step 10
- Using tweezers, grip defective gear, and pull up and out of gear system to replace.
Using tweezers, grip defective gear, and pull up and out of gear system to replace.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Lauren Roide
Member since: 04/16/2019
739 Reputation
5 Guides authored
Badges:
9
+6 more badges
Team
Cal Poly, Team S1-G1, Maness Spring 2019
Member of Cal Poly, Team S1-G1, Maness Spring 2019
CPSU-MANESS-S19S1G1
4 Members
5 Guides authored
Javier Perez - Dec 2, 2019
Reply
This is super useful guide and picture are clear for the steps. Will be excellent to know where to buy these gears replacements?
