Difficulty

Moderate

Steps

7

Time Required

                          15 - 25 minutes

Sections

4

  • Rear / Battery Cover
  • 3 steps
  • Battery
  • 1 step
  • Logic Board
  • 2 steps
  • Earpiece
  • 1 step

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSony Xperia Z2

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Please SUBSCRIBE to my channel ツ

What you need

Video Overview

Step 1

              Rear / Battery Cover
  • Switch off the phone.
  • If you can’t switch it off, you can use the OFF button near to the SIM card Tray.
  • Warm the Back Cover. You can use a hairdryer.
  • Be careful, the Back Cover is plastic.

Switch off the phone.

If you can’t switch it off, you can use the OFF button near to the SIM card Tray.

Warm the Back Cover. You can use a hairdryer.

Be careful, the Back Cover is plastic.

1024

Step 2

  • Use a small suction cup and plastic tools for separating the Rear panel.
  • There is Adhesive tape on the edges of the phone and some between the Battery and the Back Cover, as well. I found a small tab to pull just inside the top of the cover that removed the adhesive and released the back panel from the battery. Its that same style adhesive strip as used in the Iphone 5/5c/5s.

Use a small suction cup and plastic tools for separating the Rear panel.

There is Adhesive tape on the edges of the phone and some between the Battery and the Back Cover, as well. I found a small tab to pull just inside the top of the cover that removed the adhesive and released the back panel from the battery. Its that same style adhesive strip as used in the Iphone 5/5c/5s.

Step 3

  • Before installing the new cover, you must clean the phone from the old adhesive tape and install a new one (if your spare part has come without double sided adhesive tape).

Before installing the new cover, you must clean the phone from the old adhesive tape and install a new one (if your spare part has come without double sided adhesive tape).

Step 4

              Battery
  • Disconnect the Battery Flex Cable and remove the two Philips screws.
  • Li-Polymer Battery, 3.8V, 3200mAh
  • Part number: LIS1543ERPC
  • Please SUBSCRIBE to my channel ツ

Disconnect the Battery Flex Cable and remove the two Philips screws.

Li-Polymer Battery, 3.8V, 3200mAh

Part number: LIS1543ERPC

Step 5

              Logic Board
  • Disconnect one by one:
  • Magnetic Charging Dock Flex Cable
  • Volume / Power Button and Microphone Flex Cable
  • Main Camera
  • Audio Jack and Light Sensor Flex cable
  • Coaxial Antenna Cable

Disconnect one by one:

Magnetic Charging Dock Flex Cable

Volume / Power Button and Microphone Flex Cable

Main Camera

Audio Jack and Light Sensor Flex cable

Coaxial Antenna Cable

Step 6

  • Took the Logic Board, making it pick up first on the left side
  • Be careful not to tear up a cable.
  • .
  • Please SUBSCRIBE to my channel ツ

Took the Logic Board, making it pick up first on the left side

Be careful not to tear up a cable.

.

Step 7

              Earpiece
  • Earpiece
  • Part Number: VWRS087 / ZVRS087
  • .
  • Please SUBSCRIBE to my channel ツ

Earpiece

Part Number: VWRS087 / ZVRS087

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 1 other contributor 


                    ZFix

Member since: 12/09/2013

187,195 Reputation

                                      330 Guides authored                  



                       Badges:
                       35







                                                        +32 more badges

Team

                       Master Techs                        

                                                  Member of Master Techs 



                    Community                     


                                            310 Members                     


                                            1,168 Guides authored

Claes - Apr 2, 2016

Reply

Since the phone is waterresistance the headjack and earpiece are taped to the body which makes that you need to buy a new sparepart, but look out on ebay that you get a part with tape to it.

Claes - Apr 26, 2016

After having done the removal of the earpiece you will have to, either buy a new adhesive for the earpice or a new earpiece. But be aware some spareparts are sold without adhesive.

Mahtab - Dec 12, 2016

Reply

I accidentally torn apart one of the cables( vibrate cable:the brown one) I’m messed up! Vibration not working. What can I do? Where can I buy one of those cables? Please reply!