Difficulty

Difficult

Steps

12

Time Required

                          55 minutes - 1 hour

Sections

3

  • Battery
  • 5 steps
  • Motherboard
  • 5 steps
  • Charging Port
  • 2 steps

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

  • BackSony Xperia Z1s

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

The charging port is the connection between your charger and battery. A faulty charging port might cause your phone to not charge or charge very slowly.

This guide requires that you have the necessary equipment and knowledge of desoldering and soldering connections. If you want to learn the skills needed for soldering, please refer to the following guide: How To Solder and Desolder Connections.

Before beginning this guide, turn off your phone completely and remove it from any external power source.

What you need

Step 1

              Battery
  • Insert the opening pick in the crease between the rear cover and the body of the phone.
  • Pry along the edge to lift and remove the back cover.

Insert the opening pick in the crease between the rear cover and the body of the phone.

Pry along the edge to lift and remove the back cover.

1024

Step 2

  • Using the T4 Torx screwdriver, remove five 5 mm screws from the panel above the battery.
  • Remove the panel by grabbing its bottom edge and lifting upwards.

Using the T4 Torx screwdriver, remove five 5 mm screws from the panel above the battery.

Remove the panel by grabbing its bottom edge and lifting upwards.

Step 3

  • Use the opening pick to pry off the battery flex cable.

Use the opening pick to pry off the battery flex cable.

Step 4

  • Using the T4 Torx screwdriver, remove two 5 mm screws from the bottom corners of the battery.

Using the T4 Torx screwdriver, remove two 5 mm screws from the bottom corners of the battery.

Step 5

  • Firmly press the suction cup onto the battery.
  • Pull the battery out using the suction handle.

Firmly press the suction cup onto the battery.

Pull the battery out using the suction handle.

Step 6

              Motherboard
  • Use the opening pick to pry off the camera flex cable.
  • Continue to lift the flex cable upward until the camera pops out.

Use the opening pick to pry off the camera flex cable.

Continue to lift the flex cable upward until the camera pops out.

Step 7

  • Use the opening pick to pry off the three flex cables on the bottom of the motherboard.
  • Do the same for the one flex cable at the top of the motherboard.

Use the opening pick to pry off the three flex cables on the bottom of the motherboard.

Do the same for the one flex cable at the top of the motherboard.

Step 8

  • Use the opening pick to pry off the black plastic cover above the top of the motherboard.

Use the opening pick to pry off the black plastic cover above the top of the motherboard.

Step 9

  • Use a pair of tweezers to lift up the motherboard.
  • If you are having trouble removing the motherboard, try lifting up the left edge first and sliding the rest of the motherboard out.

Use a pair of tweezers to lift up the motherboard.

If you are having trouble removing the motherboard, try lifting up the left edge first and sliding the rest of the motherboard out.

Step 10

  • Use a pair of tweezers to remove the pin connection on the motherboard.
  • Fully remove the motherboard from the device.

Use a pair of tweezers to remove the pin connection on the motherboard.

Fully remove the motherboard from the device.

Step 11

              Charging Port
  • Use the soldering iron to desolder and loosen the charging port from the motherboard.
  • For more information on soldering and desoldering connections, please visit the How to Solder and Desolder Connections guide.

Use the soldering iron to desolder and loosen the charging port from the motherboard.

For more information on soldering and desoldering connections, please visit the How to Solder and Desolder Connections guide.

Step 12

  • Use a pair of tweezers to remove the charging port from the device.

Use a pair of tweezers to remove the charging port from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Jacob Willey

Member since: 09/28/2021

85 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       Clemson, Team 4-4, Hunter Fall 2021                        

                                                  Member of Clemson, Team 4-4, Hunter Fall 2021 



                    CLEM-HUNTER-F21S4G4                     


                                            5 Members                     


                                            5 Guides authored