Difficulty

Moderate

Steps

17

Time Required

Suggest a time??

Sections

5

  • Back Cover
  • 3 steps
  • Battery
  • 4 steps
  • External Speaker
  • 5 steps
  • Motherboard
  • 4 steps
  • Earpiece Speaker
  • 1 step

Flags

0

  • BackSony Xperia Z1 Compact

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover               
  • Heat along the edges of the back cover using a heat gun to soften the glue.

Heat along the edges of the back cover using a heat gun to soften the glue.

1024

Step 2

  • Attach the small suction cup to the back cover near the bottom of the phone.
  • Pull up on the suction cup and insert the plastic opening tool in between the back cover and the rest of the phone.

Attach the small suction cup to the back cover near the bottom of the phone.

Pull up on the suction cup and insert the plastic opening tool in between the back cover and the rest of the phone.

Step 3

  • Move the spudger around the edge of the back cover to separate it from the black adhesive.
  • Separating the back cover from the rest of the phone ruins the adhesive which makes it no longer waterproof.

Move the spudger around the edge of the back cover to separate it from the black adhesive.

Separating the back cover from the rest of the phone ruins the adhesive which makes it no longer waterproof.

Step 4

              Battery               
  • Carefully disconnect the battery from the logic board by using the plastic spudger as a lever.

Carefully disconnect the battery from the logic board by using the plastic spudger as a lever.

Step 5

  • Remove the single 1 x 3.0 mm screw holding the battery in using the JIS #00 screwdriver.

Remove the single 1 x 3.0 mm screw holding the battery in using the JIS #00 screwdriver.

Step 6

  • Pry the battery up from the ends using the plastic spudger until the battery pops out of the enclosure.

Pry the battery up from the ends using the plastic spudger until the battery pops out of the enclosure.

Step 7

  • Remove the battery from the device

Remove the battery from the device

Step 8

              External Speaker               
  • Unscrew the four screws on the corners of the back frame using the JIS #00 screwdriver.

Unscrew the four screws on the corners of the back frame using the JIS #00 screwdriver.

Step 9

  • Wedge the plastic opening tool under the back frame. Move the plastic opening tool around the entire frame to separate it from the adhesive.

Wedge the plastic opening tool under the back frame. Move the plastic opening tool around the entire frame to separate it from the adhesive.

Step 10

  • Remove the back frame.

Remove the back frame.

Step 11

  • Wedge the spudger underneath the external speaker. Pull up on the external speaker using the spudger.

Wedge the spudger underneath the external speaker. Pull up on the external speaker using the spudger.

Step 12

  • Remove the external speaker.

Remove the external speaker.

Step 13

              Motherboard               
  • Remove the square rubber gasket from the camera using the plastic spudger.

Remove the square rubber gasket from the camera using the plastic spudger.

Step 14

  • Remove the black plastic corner still holding in the motherboard.

Remove the black plastic corner still holding in the motherboard.

Step 15

  • Carefully pry up on the four sides of the motherboard using the plastic spudger til it separates from the base of the phone.

Carefully pry up on the four sides of the motherboard using the plastic spudger til it separates from the base of the phone.

Step 16

  • Remove the motherboard from the device.
  • There may be a small yellow adhesive underneath the motherboard still holding it in. Slide the tip of the spudger through it to sever it.

Remove the motherboard from the device.

There may be a small yellow adhesive underneath the motherboard still holding it in. Slide the tip of the spudger through it to sever it.

Step 17

              Earpiece Speaker               
  • Pry up on the earpiece from the left side to remove it.
  • There is a strong adhesive below the ear piece.

Pry up on the earpiece from the left side to remove it.

There is a strong adhesive below the ear piece.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 5 other contributors 

                    Frani Morris                     

Member since: 09/21/2017

222 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges                           

Team

                       Washington State, Team S4-G1, Phelps-Hillen Fall 2017                        

                                                  Member of Washington State, Team S4-G1, Phelps-Hillen Fall 2017 



                    WSU-PHELPS-HILLEN-F17S4G1                     


                                            6 Members                     


                                            9 Guides authored