Difficulty
Moderate
Steps
19
Time Required
15 minutes
Sections
7
- Back Assembly
- 6 steps
- Battery
- 3 steps
- Antenna Module
- 2 steps
- Front Camera
- 1 step
- Headphone Jack
- 2 steps
- Back Camera
- 1 step
- Motherboard
- 4 steps
Flags
0
BackSony Xperia XA1 Ultra
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Assembly
- Wedge your finger under the bottom ridge of the SD card insert.
- Pull outwards with your fingers to remove the SD card from the left side of device.
Wedge your finger under the bottom ridge of the SD card insert.
Pull outwards with your fingers to remove the SD card from the left side of device.
1024
Step 2
- Use a hair dryer to heat each corner of the phone.
- Alternate heating each corner for a minute to loosen the adhesive binding the back cover to the phone.
- Don’t heat one area for too long; the phone may get damaged from overheating.
Use a hair dryer to heat each corner of the phone.
Alternate heating each corner for a minute to loosen the adhesive binding the back cover to the phone.
Don’t heat one area for too long; the phone may get damaged from overheating.
Step 3
- Press a suction cup on a heated corner of the device.
- Hold the phone down and gently lift the suction cup to create a small gap.
- You may hear crunching or popping sounds when you lift up the back cover.
Press a suction cup on a heated corner of the device.
Hold the phone down and gently lift the suction cup to create a small gap.
You may hear crunching or popping sounds when you lift up the back cover.
Step 4
- Insert your iFixit Opening Tool in the small gap between your phone and the back cover.
- Lift up on the iFixit Opening Tool and insert your plastic card in the small gap between your phone and the back cover.
Insert your iFixit Opening Tool in the small gap between your phone and the back cover.
Lift up on the iFixit Opening Tool and insert your plastic card in the small gap between your phone and the back cover.
Step 5
- Slide your plastic card along the side of your phone to loosen the adhesive.
- Move the card along the sides of the phone to lift all of the corners.
Slide your plastic card along the side of your phone to loosen the adhesive.
Move the card along the sides of the phone to lift all of the corners.
Step 6
- Lift up the back cover by lifting up the sides of the phone with your hand.
- Apply a new strip of adhesive for reassembly.
Lift up the back cover by lifting up the sides of the phone with your hand.
Apply a new strip of adhesive for reassembly.
Step 7
Battery
- Peel off the two pieces of black tape covering the battery with your hands.
Peel off the two pieces of black tape covering the battery with your hands.
Step 8
- Use the iFixit Opening Tool to remove the flexible orange strip which connects the battery to the motherboard.
Use the iFixit Opening Tool to remove the flexible orange strip which connects the battery to the motherboard.
Step 9
- Wedge the iFixit Opening Tool underneath the battery.
- Remove the battery by pulling up on the iFixit Opening Tool.
Wedge the iFixit Opening Tool underneath the battery.
Remove the battery by pulling up on the iFixit Opening Tool.
Step 10
Antenna Module
- Remove the four 4mm T5 screws on the top of the black panel securing the antenna module to the device.
Remove the four 4mm T5 screws on the top of the black panel securing the antenna module to the device.
Step 11
- Insert your iFixit Opening Tool underneath the antenna module.
- Lift up gently with the iFixit Opening Tool to remove the antenna module.
- The antenna module may be difficult to remove.
Insert your iFixit Opening Tool underneath the antenna module.
Lift up gently with the iFixit Opening Tool to remove the antenna module.
The antenna module may be difficult to remove.
Step 12
Front Camera
- Insert your iFixit Opening Tool underneath the front camera and gently lift up.
- Remove the front camera by lifting the front camera up with your hands.
Insert your iFixit Opening Tool underneath the front camera and gently lift up.
Remove the front camera by lifting the front camera up with your hands.
Step 13
Headphone Jack
- Remove the 4mm T5 screw connecting the headphone jack to the panel.
Remove the 4mm T5 screw connecting the headphone jack to the panel.
Step 14
- Use your iFixit Opening Tool to lift and disconnect the headphone jack connector piece.
- The small black piece connected to the headphone jack that is holding the single screw in place has broken off in the device shown.
Use your iFixit Opening Tool to lift and disconnect the headphone jack connector piece.
The small black piece connected to the headphone jack that is holding the single screw in place has broken off in the device shown.
Step 15
Back Camera
- Insert your iFixit Opening Tool between the back camera and the motherboard and gently lift up.
- Lift up with the iFixit Opening Tool until the back camera is removed from the device.
Insert your iFixit Opening Tool between the back camera and the motherboard and gently lift up.
Lift up with the iFixit Opening Tool until the back camera is removed from the device.
Step 16
Motherboard
- Remove the two 4mm T5 screws connecting the motherboard to the device.
Remove the two 4mm T5 screws connecting the motherboard to the device.
Step 17
- Use your flat head tweezers to remove the black wire connected to the motherboard.
- Use your flat head tweezers to remove the white wire connected to the motherboard.
- There are only two wires connected to the motherboard.
Use your flat head tweezers to remove the black wire connected to the motherboard.
Use your flat head tweezers to remove the white wire connected to the motherboard.
There are only two wires connected to the motherboard.
Step 18
- Use your iFixit Opening Tool to remove the main flex (the middle orange tab) from the motherboard.
- Use your iFixit Opening Tool to remove the power button flex (the left orange tab) from the motherboard.
Use your iFixit Opening Tool to remove the main flex (the middle orange tab) from the motherboard.
Use your iFixit Opening Tool to remove the power button flex (the left orange tab) from the motherboard.
Step 19
- Wedge your iFixit opening tool under the motherboard.
- Lift up with your iFixit Opening Tool to lift the motherboard from the device.
Wedge your iFixit opening tool under the motherboard.
Lift up with your iFixit Opening Tool to lift the motherboard from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Jacob Jung
Member since: 04/18/2018
1,417 Reputation
9 Guides authored
Badges:
12
+9 more badges
Team
Cal Poly, Team S16-G3, Livingston Spring 2018
Member of Cal Poly, Team S16-G3, Livingston Spring 2018
CPSU-LIVINGSTON-S18S16G3
4 Members
9 Guides authored
obivinn - Jul 9, 2018
Reply
where can i place an order for the motherboard
Timothy Tomon - Jul 12, 2018
yeah. Where??