Sony Xperia Xa1 Ultra Lcd Display Touchscreen Digitizer Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 minutes

Sections

Back Assembly
6 steps
Battery
3 steps
Antenna Module
2 steps
Front Camera
1 step
Headphone Jack
2 steps
Back Camera
1 step
Motherboard
4 steps
LCD Display Touchscreen Digitizer
16 steps

Flags

BackSony Xperia XA1 Ultra
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Assembly

Wedge your finger under the bottom ridge of the SD card insert.
Pull outwards with your fingers to remove the SD card from the left side of device.

Wedge your finger under the bottom ridge of the SD card insert.

Pull outwards with your fingers to remove the SD card from the left side of device.

1024

Step 2

Use a hair dryer to heat each corner of the phone.
Alternate heating each corner for a minute to loosen the adhesive binding the back cover to the phone.
Don’t heat one area for too long; the phone may get damaged from overheating.

Use a hair dryer to heat each corner of the phone.

Alternate heating each corner for a minute to loosen the adhesive binding the back cover to the phone.

Don’t heat one area for too long; the phone may get damaged from overheating.

Step 3

Press a suction cup on a heated corner of the device.
Hold the phone down and gently lift the suction cup to create a small gap.
You may hear crunching or popping sounds when you lift up the back cover.

Press a suction cup on a heated corner of the device.

Hold the phone down and gently lift the suction cup to create a small gap.

You may hear crunching or popping sounds when you lift up the back cover.

Step 4

Insert your iFixit Opening Tool in the small gap between your phone and the back cover.
Lift up on the iFixit Opening Tool and insert your plastic card in the small gap between your phone and the back cover.

Insert your iFixit Opening Tool in the small gap between your phone and the back cover.

Lift up on the iFixit Opening Tool and insert your plastic card in the small gap between your phone and the back cover.

Step 5

Slide your plastic card along the side of your phone to loosen the adhesive.
Move the card along the sides of the phone to lift all of the corners.

Slide your plastic card along the side of your phone to loosen the adhesive.

Move the card along the sides of the phone to lift all of the corners.

Step 6

Lift up the back cover by lifting up the sides of the phone with your hand.
Apply a new strip of adhesive for reassembly.

Lift up the back cover by lifting up the sides of the phone with your hand.

Apply a new strip of adhesive for reassembly.

Step 7

              Battery

Peel off the two pieces of black tape covering the battery with your hands.

Peel off the two pieces of black tape covering the battery with your hands.

Step 8

Use the iFixit Opening Tool to remove the flexible orange strip which connects the battery to the motherboard.

Use the iFixit Opening Tool to remove the flexible orange strip which connects the battery to the motherboard.

Step 9

Wedge the iFixit Opening Tool underneath the battery.
Remove the battery by pulling up on the iFixit Opening Tool.

Wedge the iFixit Opening Tool underneath the battery.

Remove the battery by pulling up on the iFixit Opening Tool.

Step 10

              Antenna Module

Remove the four 4mm T5 screws on the top of the black panel securing the antenna module to the device.

Remove the four 4mm T5 screws on the top of the black panel securing the antenna module to the device.

Step 11

Insert your iFixit Opening Tool underneath the antenna module.
Lift up gently with the iFixit Opening Tool to remove the antenna module.
The antenna module may be difficult to remove.

Insert your iFixit Opening Tool underneath the antenna module.

Lift up gently with the iFixit Opening Tool to remove the antenna module.

The antenna module may be difficult to remove.

Step 12

              Front Camera

Insert your iFixit Opening Tool underneath the front camera and gently lift up.
Remove the front camera by lifting the front camera up with your hands.

Insert your iFixit Opening Tool underneath the front camera and gently lift up.

Remove the front camera by lifting the front camera up with your hands.

Step 13

              Headphone Jack

Remove the 4mm T5 screw connecting the headphone jack to the panel.

Remove the 4mm T5 screw connecting the headphone jack to the panel.

Step 14

Use your iFixit Opening Tool to lift and disconnect the headphone jack connector piece.
The small black piece connected to the headphone jack that is holding the single screw in place has broken off in the device shown.

Use your iFixit Opening Tool to lift and disconnect the headphone jack connector piece.

The small black piece connected to the headphone jack that is holding the single screw in place has broken off in the device shown.

Step 15

              Back Camera

Insert your iFixit Opening Tool between the back camera and the motherboard and gently lift up.
Lift up with the iFixit Opening Tool until the back camera is removed from the device.

Insert your iFixit Opening Tool between the back camera and the motherboard and gently lift up.

Lift up with the iFixit Opening Tool until the back camera is removed from the device.

Step 16

              Motherboard

Remove the two 4mm T5 screws connecting the motherboard to the device.

Remove the two 4mm T5 screws connecting the motherboard to the device.

Step 17

Use your flat head tweezers to remove the black wire connected to the motherboard.
Use your flat head tweezers to remove the white wire connected to the motherboard.
There are only two wires connected to the motherboard.

Use your flat head tweezers to remove the black wire connected to the motherboard.

Use your flat head tweezers to remove the white wire connected to the motherboard.

There are only two wires connected to the motherboard.

Step 18

Use your iFixit Opening Tool to remove the main flex (the middle orange tab) from the motherboard.
Use your iFixit Opening Tool to remove the power button flex (the left orange tab) from the motherboard.

Use your iFixit Opening Tool to remove the main flex (the middle orange tab) from the motherboard.

Use your iFixit Opening Tool to remove the power button flex (the left orange tab) from the motherboard.

Step 19

Wedge your iFixit opening tool under the motherboard.
Lift up with your iFixit Opening Tool to lift the motherboard from the device.

Wedge your iFixit opening tool under the motherboard.

Lift up with your iFixit Opening Tool to lift the motherboard from the device.

Step 20

              LCD Display Touchscreen Digitizer

Wedge your flathead tweezers under the earpiece.
Lift up with your flat head tweezers to remove the earpiece from the device.

Wedge your flathead tweezers under the earpiece.

Lift up with your flat head tweezers to remove the earpiece from the device.

Step 21

Wedge your flathead tweezers under the flashlight module.
Lift up with your flat head tweezers to remove the flashlight module from your device.

Wedge your flathead tweezers under the flashlight module.

Lift up with your flat head tweezers to remove the flashlight module from your device.

Step 22

Grab the power flex from the charging port PCB board with your flathead tweezers.
Lift up with your flathead tweezers to remove the power flex from the charging port PCB board.

Grab the power flex from the charging port PCB board with your flathead tweezers.

Lift up with your flathead tweezers to remove the power flex from the charging port PCB board.

Step 23

Grab the vibration motor connected to the charging port PCB board with your flathead tweezers.
Lift up with your flathead tweezers to remove the vibration motor.

Grab the vibration motor connected to the charging port PCB board with your flathead tweezers.

Lift up with your flathead tweezers to remove the vibration motor.

Step 24

Grab the black wire connected to the charging port PCB board with your flathead tweezers.
Pull up on the black wire with your flathead tweezers to disconnect the black wire from the charging port PCB board.

Grab the black wire connected to the charging port PCB board with your flathead tweezers.

Pull up on the black wire with your flathead tweezers to disconnect the black wire from the charging port PCB board.

Step 25

Grab the white wire connected to the charging port PCB board using your flathead tweezers.
Pull up on the white wire with your flathead tweezers to disconnect the white wire from the charging port PCB board.

Grab the white wire connected to the charging port PCB board using your flathead tweezers.

Pull up on the white wire with your flathead tweezers to disconnect the white wire from the charging port PCB board.

Step 26

Wedge your iFixit Opening Tool under the charging port PCB board.
Pull up with your iFixit Opening Tool to remove the charging port PCB board.

Wedge your iFixit Opening Tool under the charging port PCB board.

Pull up with your iFixit Opening Tool to remove the charging port PCB board.

Step 27

Remove the five 4mm T5 screws connecting the side panel to the power button flex cable.

Remove the five 4mm T5 screws connecting the side panel to the power button flex cable.

Step 28

Use your hands to grab the side panel of the device.
Pull your hands away from the device to remove the side panel.

Use your hands to grab the side panel of the device.

Pull your hands away from the device to remove the side panel.

Step 29

Remove the five 4mm T5 screws connecting the SD card side panel to the device.

Remove the five 4mm T5 screws connecting the SD card side panel to the device.

Step 30

Remove the SD card side panel from the device by grabbing the SD card side panel with your hands and sliding the SD card side panel away from the device.

Remove the SD card side panel from the device by grabbing the SD card side panel with your hands and sliding the SD card side panel away from the device.

Step 31

Grab the two pieces of black tape holding down the battery with your hands.
Lift up with your hands to remove the two black pieces of tape that hold down the battery.

Grab the two pieces of black tape holding down the battery with your hands.

Lift up with your hands to remove the two black pieces of tape that hold down the battery.

Step 32

Peel off the power button flex with your hands.

Peel off the power button flex with your hands.

Step 33

Remove the white wire from the device using your hands.

Remove the white wire from the device using your hands.

Step 34

Remove the black wire from the device using your hands.

Remove the black wire from the device using your hands.

Step 35

The LCD Display Touch Screen Digitizer should be the only part left.

The LCD Display Touch Screen Digitizer should be the only part left.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 4 other contributors

                    Jacob Jung

Member since: 04/18/2018

1,417 Reputation

                                      9 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Cal Poly, Team S16-G3, Livingston Spring 2018                        

                                                  Member of Cal Poly, Team S16-G3, Livingston Spring 2018 



                    CPSU-LIVINGSTON-S18S16G3                     


                                            4 Members                     


                                            9 Guides authored

Taken Out - Oct 16, 2018

Thanks for the help! Any chance you know where to get the side panels/bars? searched everywhere and cant find them

Musa Zwane - Mar 11, 2020

Any chance one can replace the outta glass only? touch feature still works :(

Introduction#

What you need#

Team#

Introduction

What you need

Team