Difficulty
Easy
Steps
9
Time Required
20 seconds
Sections
3
- Back Assembly
- 6 steps
- Antenna Module
- 2 steps
- Front Camera
- 1 step
Flags
0
BackSony Xperia XA1 Ultra
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Assembly
- Wedge your finger under the bottom ridge of the SD card insert.
- Pull outwards with your fingers to remove the SD card from the left side of device.
Wedge your finger under the bottom ridge of the SD card insert.
Pull outwards with your fingers to remove the SD card from the left side of device.
1024
Step 2
- Use a hair dryer to heat each corner of the phone.
- Alternate heating each corner for a minute to loosen the adhesive binding the back cover to the phone.
- Don’t heat one area for too long; the phone may get damaged from overheating.
Use a hair dryer to heat each corner of the phone.
Alternate heating each corner for a minute to loosen the adhesive binding the back cover to the phone.
Don’t heat one area for too long; the phone may get damaged from overheating.
Step 3
- Press a suction cup on a heated corner of the device.
- Hold the phone down and gently lift the suction cup to create a small gap.
- You may hear crunching or popping sounds when you lift up the back cover.
Press a suction cup on a heated corner of the device.
Hold the phone down and gently lift the suction cup to create a small gap.
You may hear crunching or popping sounds when you lift up the back cover.
Step 4
- Insert your iFixit Opening Tool in the small gap between your phone and the back cover.
- Lift up on the iFixit Opening Tool and insert your plastic card in the small gap between your phone and the back cover.
Insert your iFixit Opening Tool in the small gap between your phone and the back cover.
Lift up on the iFixit Opening Tool and insert your plastic card in the small gap between your phone and the back cover.
Step 5
- Slide your plastic card along the side of your phone to loosen the adhesive.
- Move the card along the sides of the phone to lift all of the corners.
Slide your plastic card along the side of your phone to loosen the adhesive.
Move the card along the sides of the phone to lift all of the corners.
Step 6
- Lift up the back cover by lifting up the sides of the phone with your hand.
- Apply a new strip of adhesive for reassembly.
Lift up the back cover by lifting up the sides of the phone with your hand.
Apply a new strip of adhesive for reassembly.
Step 7
Antenna Module
- Remove the four 4mm T5 screws on the top of the black panel securing the antenna module to the device.
Remove the four 4mm T5 screws on the top of the black panel securing the antenna module to the device.
Step 8
- Insert your iFixit Opening Tool underneath the antenna module.
- Lift up gently with the iFixit Opening Tool to remove the antenna module.
- The antenna module may be difficult to remove.
Insert your iFixit Opening Tool underneath the antenna module.
Lift up gently with the iFixit Opening Tool to remove the antenna module.
The antenna module may be difficult to remove.
Step 9
Front Camera
- Insert your iFixit Opening Tool underneath the front camera and gently lift up.
- Remove the front camera by lifting the front camera up with your hands.
Insert your iFixit Opening Tool underneath the front camera and gently lift up.
Remove the front camera by lifting the front camera up with your hands.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Jacob Jung
Member since: 04/18/2018
1,417 Reputation
9 Guides authored
Badges:
12
+9 more badges
Team
Cal Poly, Team S16-G3, Livingston Spring 2018
Member of Cal Poly, Team S16-G3, Livingston Spring 2018
CPSU-LIVINGSTON-S18S16G3
4 Members
9 Guides authored
