Difficulty
Very difficult
Steps
8
Time Required
30 minutes
Sections
2
- Rear Bezel
- 2 steps
- Touch Screen
- 6 steps
Flags
1
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackSony Xperia E3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
D2202, D2203, D2206, D2243, D2202
What you need
Video Overview
Step 1
Turn of the Phone
- Turn off the device
- Remove the SIM and the memory cards.
- Remove 4x rubber corners.
- There are 6x black screws Torx T4, remove them.
Turn off the device
Remove the SIM and the memory cards.
Remove 4x rubber corners.
There are 6x black screws Torx T4, remove them.
1024
Step 2
Rear Cover Removal
- Use a plastic tool and separate the rear bezel.
- Be careful for the side buttons.
Use a plastic tool and separate the rear bezel.
Be careful for the side buttons.
Step 3
Touch Screen Flex Cable
- Disconnect the touch screen flex cable.
- Disconnect the battery flex cable.
Disconnect the touch screen flex cable.
Disconnect the battery flex cable.
Step 4
- With a hair dryer or heat gun warm the glass, at first for about 2-3 minutes.
- Use a thin plastic tool, like a plastic pick and start the separation from the underside.
- Do this very slow and periodically warm the glass!
- At the beginning you have to separate the touch screen glass from the main frame.
With a hair dryer or heat gun warm the glass, at first for about 2-3 minutes.
Use a thin plastic tool, like a plastic pick and start the separation from the underside.
Do this very slow and periodically warm the glass!
At the beginning you have to separate the touch screen glass from the main frame.
Step 5
- Now continue with a plastic card.
- AGAIN!!! Very slowly and periodically worm the glass.
- The LCD is thin less than a millimeter!
- Remove the touch screen.
Now continue with a plastic card.
AGAIN!!! Very slowly and periodically worm the glass.
The LCD is thin less than a millimeter!
Remove the touch screen.
Step 6
- Now is time to test the phone.
- If the LCD is OK you can order only a touch screen, if no, then you need display assembly - touch screen & LCD
- With a plastic pick gently scrape the glue.
- With a cloth and isopropyl alcohol clean the LCD.
- Don’t use a lot of alcohol. if the liquid passes behind the LCD, will appear spots that you can’t remove.
Now is time to test the phone.
If the LCD is OK you can order only a touch screen, if no, then you need display assembly - touch screen & LCD
With a plastic pick gently scrape the glue.
With a cloth and isopropyl alcohol clean the LCD.
Don’t use a lot of alcohol. if the liquid passes behind the LCD, will appear spots that you can’t remove.
Step 7
- On the new touch screen or on the main frame put adhesive sticker 3mm.
- Be careful not to cover the the places for the camera, sensor, earpiece, etc.
- Lift the logic board a little bit, so that the touch screen flex cable can pass.
- It’s easier if you can order the touch screen together with adhesive which is cut off specifically for model.
On the new touch screen or on the main frame put adhesive sticker 3mm.
Be careful not to cover the the places for the camera, sensor, earpiece, etc.
Lift the logic board a little bit, so that the touch screen flex cable can pass.
It’s easier if you can order the touch screen together with adhesive which is cut off specifically for model.
Step 8
- Reassemble the device.
- That’s all.
Reassemble the device.
That’s all.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 1 other contributor
ZFix
Member since: 12/09/2013
187,195 Reputation
330 Guides authored
Badges:
35
+32 more badges
Team
Master Techs
Member of Master Techs
Community
310 Members
1,168 Guides authored