Difficulty

Moderate

Steps

14

Time Required

                          55 minutes

Sections

5

  • USB Cable
  • 5 steps
  • Motherboard
  • 2 steps
  • Display
  • 2 steps
  • Display Board
  • 4 steps
  • Volume Knob
  • 1 step

Flags

0

  • BackSony XAV-AX100

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              USB Cable
  • Place the device on a flat surface, upside down, so the bottom of the screen would be facing upwards.
  • Remove the ten 3.5mm Phillips #0 screws from the back plate.

Place the device on a flat surface, upside down, so the bottom of the screen would be facing upwards.

Remove the ten 3.5mm Phillips #0 screws from the back plate.

1024

Step 2

  • Use a plastic opening tool to remove the back plate.
  • Don’t remove completely as there will still be cables connected.

Use a plastic opening tool to remove the back plate.

Don’t remove completely as there will still be cables connected.

Step 3

  • Disconnect the USB cable from the display board.

Disconnect the USB cable from the display board.

Step 4

  • Adjust the rubber holders that are keeping the USB cable still on the motherboard, so you can remove the cable entirely from the inner compartment.
  • The rubber holders are extremely sensitive to any applied force. Therefore, be careful while turning them around.

Adjust the rubber holders that are keeping the USB cable still on the motherboard, so you can remove the cable entirely from the inner compartment.

The rubber holders are extremely sensitive to any applied force. Therefore, be careful while turning them around.

Step 5

  • Remove the 3.5mm Phillip #0 screw that secures the USB cable to the back panel.
  • Pull the USB cable off of the back plate.

Remove the 3.5mm Phillip #0 screw that secures the USB cable to the back panel.

Pull the USB cable off of the back plate.

Step 6

              Motherboard
  • Disconnect the display power cable from the motherboard.
  • Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.

Disconnect the display power cable from the motherboard.

Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.

Step 7

  • Unscrew the four 3.5mm Phillips #0 screws from the motherboard.
  • Use a spudger to gently lift the motherboard up and out of the radio.

Unscrew the four 3.5mm Phillips #0 screws from the motherboard.

Use a spudger to gently lift the motherboard up and out of the radio.

Step 8

              Display
  • Remove the four 3.5mm Phillips #0 screws from the sides of the display.

Remove the four 3.5mm Phillips #0 screws from the sides of the display.

Step 9

  • Remove two 3.5mm Phillips #0 screws from the back of the head unit.

Remove two 3.5mm Phillips #0 screws from the back of the head unit.

Step 10

              Display Board
  • Remove the four 3.5mm Phillips #0 screws from the display board.
  • Remove the black tape using a precise tweezer.
  • Remove the 3.5mm Phillips #0 screw from underneath the tape.

Remove the four 3.5mm Phillips #0 screws from the display board.

Remove the black tape using a precise tweezer.

Remove the 3.5mm Phillips #0 screw from underneath the tape.

Step 11

  • Remove the two 2mm Phillips #0 screws from the back plate.
  • Remove the back plate.

Remove the two 2mm Phillips #0 screws from the back plate.

Remove the back plate.

Step 12

  • Remove the single 2mm Phillips #0 screw from the motherboard.
  • Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.

Remove the single 2mm Phillips #0 screw from the motherboard.

Step 13

  • Use a plastic opening tool to remove the display board from the radio.

Use a plastic opening tool to remove the display board from the radio.

Step 14

              Volume Knob
  • Remove the silver knob cover by pulling upwards on it.
  • Remove the plastic face plate.
  • Pull off the black knob.

Remove the silver knob cover by pulling upwards on it.

Remove the plastic face plate.

Pull off the black knob.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Abdulaziz Redha

Member since: 02/22/2018

741 Reputation

                                      5 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       USF Tampa, Team S1-G5, Cagle Spring 2018                        

                                                  Member of USF Tampa, Team S1-G5, Cagle Spring 2018 



                    USFT-CAGLE-S18S1G5                     


                                            2 Members                     


                                            5 Guides authored