Difficulty

Moderate

Steps

9

Time Required

                          40 minutes            

Sections

3

  • USB Cable
  • 5 steps
  • Motherboard
  • 2 steps
  • Display
  • 2 steps

Flags

0

  • BackSony XAV-AX100

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              USB Cable               
  • Place the device on a flat surface, upside down, so the bottom of the screen would be facing upwards.
  • Remove the ten 3.5mm Phillips #0 screws from the back plate.

Place the device on a flat surface, upside down, so the bottom of the screen would be facing upwards.

Remove the ten 3.5mm Phillips #0 screws from the back plate.

1024

Step 2

  • Use a plastic opening tool to remove the back plate.
  • Don’t remove completely as there will still be cables connected.

Use a plastic opening tool to remove the back plate.

Don’t remove completely as there will still be cables connected.

Step 3

  • Disconnect the USB cable from the display board.

Disconnect the USB cable from the display board.

Step 4

  • Adjust the rubber holders that are keeping the USB cable still on the motherboard, so you can remove the cable entirely from the inner compartment.
  • The rubber holders are extremely sensitive to any applied force. Therefore, be careful while turning them around.

Adjust the rubber holders that are keeping the USB cable still on the motherboard, so you can remove the cable entirely from the inner compartment.

The rubber holders are extremely sensitive to any applied force. Therefore, be careful while turning them around.

Step 5

  • Remove the 3.5mm Phillip #0 screw that secures the USB cable to the back panel.
  • Pull the USB cable off of the back plate.

Remove the 3.5mm Phillip #0 screw that secures the USB cable to the back panel.

Pull the USB cable off of the back plate.

Step 6

              Motherboard               
  • Disconnect the display power cable from the motherboard.
  • Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.

Disconnect the display power cable from the motherboard.

Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.

Step 7

  • Unscrew the four 3.5mm Phillips #0 screws from the motherboard.
  • Use a spudger to gently lift the motherboard up and out of the radio.

Unscrew the four 3.5mm Phillips #0 screws from the motherboard.

Use a spudger to gently lift the motherboard up and out of the radio.

Step 8

              Display               
  • Remove the four 3.5mm Phillips #0 screws from the sides of the display.

Remove the four 3.5mm Phillips #0 screws from the sides of the display.

Step 9

  • Remove two 3.5mm Phillips #0 screws from the back of the head unit.

Remove two 3.5mm Phillips #0 screws from the back of the head unit.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.                                             

Author

                                      with 1 other contributor 

                    Abdulaziz Redha                     

Member since: 02/22/2018

741 Reputation

                                      5 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       USF Tampa, Team S1-G5, Cagle Spring 2018                        

                                                  Member of USF Tampa, Team S1-G5, Cagle Spring 2018 



                    USFT-CAGLE-S18S1G5                     


                                            2 Members                     


                                            5 Guides authored                     

Morten Hjorth-Johansen - Sep 14, 2020

Reply

Where do you get a replacement screen?

I need one for a xav 3005 db

Robert Edwards - Apr 17, 2022

Reply

Thank you very much for this great write up.

However after having performed it, if all you are doing is replacing the screen, then steps 1, 4, 5 and 7 are actually completely unnecessary . There is no need to remove the back panel or the motherboard.

but thank you nonetheless for having shown the way.