Sony Vaio Vpccw17Fx Trackpad Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Back case
7 steps
Motherboard
6 steps
Fan
3 steps
Trackpad
2 steps

Flags

BackSony Vaio VPC-CW17FX
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back case

Turn the laptop over and orient it as shown.

Turn the laptop over and orient it as shown.

1024

Step 2

Remove the battery by pinching the two lock tabs towards the center.
Next, lift up on the battery to remove it.

Remove the battery by pinching the two lock tabs towards the center.

Next, lift up on the battery to remove it.

Step 3

Using a Phillips #00 screwdriver, remove the twenty-two 5.6 mm screws from the back of the laptop.
Be sure to remove all screws, including those that are typically covered by the battery.

Using a Phillips #00 screwdriver, remove the twenty-two 5.6 mm screws from the back of the laptop.

Be sure to remove all screws, including those that are typically covered by the battery.

Step 4

Now, remove the small covers from the back of the case.
Using a Phillips #00 screwdriver, unscrew the three 5.6 mm screws from the covers (one screw on the RAM cover [middle] and two screws on the Hard Drive cover [bottom right]).
Then, lift up on and remove these covers as shown in the third image.

Now, remove the small covers from the back of the case.

Using a Phillips #00 screwdriver, unscrew the three 5.6 mm screws from the covers (one screw on the RAM cover [middle] and two screws on the Hard Drive cover [bottom right]).

Then, lift up on and remove these covers as shown in the third image.

Step 5

Remove the hard drive.
Using a Phillips #00 screwdriver, unscrew the two remaining 4.9 mm screws holding the hard drive into place.
Next, lift up and pull outwards to release the hard drive from its socket.

Remove the hard drive.

Using a Phillips #00 screwdriver, unscrew the two remaining 4.9 mm screws holding the hard drive into place.

Next, lift up and pull outwards to release the hard drive from its socket.

Step 6

Using your fingers, grasp the black tab and lightly pull up on the ribbon cable to detach it from the motherboard.

Using your fingers, grasp the black tab and lightly pull up on the ribbon cable to detach it from the motherboard.

Step 7

After proper removal of all necessary screws, gently lift up on the back case to remove it.

After proper removal of all necessary screws, gently lift up on the back case to remove it.

Step 8

              Motherboard

With your hand, grasp the side of the DVD/CD drive and gently pull it out of the socket, disconnecting it from the motherboard.

With your hand, grasp the side of the DVD/CD drive and gently pull it out of the socket, disconnecting it from the motherboard.

Step 9

Using your fingers, grasp the three ribbon cable attachments (pictured) and gently pull on them to disconnect them from the motherboard.

Using your fingers, grasp the three ribbon cable attachments (pictured) and gently pull on them to disconnect them from the motherboard.

Step 10

Repeat the previous step for the two remaining ribbon cables (one is located by the fan, while the other is located by the CD/DVD drive).
For the ribbon cable located near the fan, use your fingers to grasp the black tab and gently, yet firmly, pull up on the cable to detach it from the motherboard.

Repeat the previous step for the two remaining ribbon cables (one is located by the fan, while the other is located by the CD/DVD drive).

For the ribbon cable located near the fan, use your fingers to grasp the black tab and gently, yet firmly, pull up on the cable to detach it from the motherboard.

Step 11

Using the Phillips #00 screwdriver, remove the three 4.9 mm screws depicted here.
Next, using your fingers, lift up on this metal piece and remove it from the motherboard.

Using the Phillips #00 screwdriver, remove the three 4.9 mm screws depicted here.

Next, using your fingers, lift up on this metal piece and remove it from the motherboard.

Step 12

Using the Phillips #00 screwdriver, unscrew the two 4.9 mm screws depicted here.
Next, remove the metal cover to expose the bluetooth card.
Gently fit the flat end of a spudger under the edge of the bluetooth card. Then, lightly pry up on this edge to release the card from the motherboard. (Refer to the third image)

Using the Phillips #00 screwdriver, unscrew the two 4.9 mm screws depicted here.

Next, remove the metal cover to expose the bluetooth card.

Gently fit the flat end of a spudger under the edge of the bluetooth card. Then, lightly pry up on this edge to release the card from the motherboard. (Refer to the third image)

Step 13

Gently lift up on the now free motherboard.
Detach the two ribbon cables that connect the motherboard to the keyboard. To do this, use your fingers to gently pull on the cables until they disconnect.

Gently lift up on the now free motherboard.

Detach the two ribbon cables that connect the motherboard to the keyboard. To do this, use your fingers to gently pull on the cables until they disconnect.

Step 14

Fan

Locate the fan (top-right corner of the computer).
Using a Phillips #00 screwdriver, unscrew the six 2.7 mm screws that secure the fan to the motherboard.

Locate the fan (top-right corner of the computer).

Using a Phillips #00 screwdriver, unscrew the six 2.7 mm screws that secure the fan to the motherboard.

Step 15

This step can be skipped if you are just removing the fan to access another part of the device (such as the motherboard).
Using a Japanese Industrial Standard #00 screwdriver, unscrew four 3.7 mm screws located on the casing of the fan.

This step can be skipped if you are just removing the fan to access another part of the device (such as the motherboard).

Using a Japanese Industrial Standard #00 screwdriver, unscrew four 3.7 mm screws located on the casing of the fan.

Step 16

Using your fingers, grasp the white tab and firmly, yet gently, pull up on the wire to disconnect it from the motherboard.

Using your fingers, grasp the white tab and firmly, yet gently, pull up on the wire to disconnect it from the motherboard.

Step 17

              Trackpad

Once you have removed the motherboard, you can locate the trackpad, which is centered at the bottom of the back of the computer.
From the back, the trackpad can be identified by the single ribbon cable (pictured here).

Once you have removed the motherboard, you can locate the trackpad, which is centered at the bottom of the back of the computer.

From the back, the trackpad can be identified by the single ribbon cable (pictured here).

Step 18

Using the pointed end of a spudger, lift up on the black latch that is holding the ribbon cable in place.
Use your fingers to grasp the ribbon cable. Lightly pull on the cable until it releases.

Using the pointed end of a spudger, lift up on the black latch that is holding the ribbon cable in place.

Use your fingers to grasp the ribbon cable. Lightly pull on the cable until it releases.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Makaila Howard

Member since: 01/29/2018

430 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       University of Alabama, Team S3-G9, Bedsole Spring 2018                        

                                                  Member of University of Alabama, Team S3-G9, Bedsole Spring 2018 



                    UA-BEDSOLE-S18S3G9                     


                                            3 Members                     


                                            12 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team