Sony Vaio Vpc Y2190X Fan Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          9 - 15 minutes

Sections

Battery
3 steps
Hard Drive
3 steps
Fan
10 steps

Flags

BackSony Vaio VPC-Y2190X
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Flip your laptop so that the bottom is facing up.

Flip your laptop so that the bottom is facing up.

1024

Step 2

Slide the “Lock” switch to the right.
Slide and hold the “Release” switch to the left.

Slide the “Lock” switch to the right.

Slide and hold the “Release” switch to the left.

Step 3

While holding the “Release” switch, lift the lip of the battery.
Lift the battery up and out of the laptop.

While holding the “Release” switch, lift the lip of the battery.

Lift the battery up and out of the laptop.

Step 4

              Hard Drive

Using a #0PH screwdriver, unscrew the three 4.80mm screws on the back of the device.
The screws are held into the panel by washers, they will not fall out once unscrewed.

Using a #0PH screwdriver, unscrew the three 4.80mm screws on the back of the device.

The screws are held into the panel by washers, they will not fall out once unscrewed.

Step 5

Remove the panel.
Use the #0PH screwdriver to remove the four 3.61mm screws.

Remove the panel.

Use the #0PH screwdriver to remove the four 3.61mm screws.

Step 6

Carefully lift the hard drive.
Remove the hard drive by pulling it to the left.

Carefully lift the hard drive.

Remove the hard drive by pulling it to the left.

Step 7

Fan

Remove all nine 5.63mm screws with the #0PH screwdriver.
Remove the four 8.62mm screws with the #0PH screwdriver.

Remove all nine 5.63mm screws with the #0PH screwdriver.

Remove the four 8.62mm screws with the #0PH screwdriver.

Step 8

Flip your Vaio so that the keyboard is facing up.
Use the iFixit Opening Tool to lift the keyboard from the frame, starting at the ESC key corner.
Gently slide the iFixit Opening Tool along the edge of the keyboard.
The keyboard is connected to the frame with a wire, do not fully lift the keyboard from the frame

Flip your Vaio so that the keyboard is facing up.

Use the iFixit Opening Tool to lift the keyboard from the frame, starting at the ESC key corner.

Gently slide the iFixit Opening Tool along the edge of the keyboard.

The keyboard is connected to the frame with a wire, do not fully lift the keyboard from the frame

Step 9

The cable is located under the keyboard, just above the touchpad.
Use the iFixit Opening Tool to flip the clip up in order to release the cable.
Detach the cable from the frame.
Remove the keyboard from the frame.

The cable is located under the keyboard, just above the touchpad.

Use the iFixit Opening Tool to flip the clip up in order to release the cable.

Detach the cable from the frame.

Remove the keyboard from the frame.

Step 10

Use the iFixit Opening Tool to lift the edge of the clip from the cable.
Gently pull the cable away from the clip.
Repeat the first two steps on the second clip shown in the picture.

Use the iFixit Opening Tool to lift the edge of the clip from the cable.

Gently pull the cable away from the clip.

Repeat the first two steps on the second clip shown in the picture.

Step 11

Use the iFixit Opening Tool to detach the cable from the motherboard.
Use the small needle nose pliers to pull the cable from the motherboard.

Use the iFixit Opening Tool to detach the cable from the motherboard.

Use the small needle nose pliers to pull the cable from the motherboard.

Step 12

Use the iFixit Opening Tool to flip the clip up in order to release the first cable.
Use the small needle nose pliers to pull the second cable from where it is attached.
Use the small needle nose pliers to detach the third cable from motherboard.

Use the iFixit Opening Tool to flip the clip up in order to release the first cable.

Use the small needle nose pliers to pull the second cable from where it is attached.

Use the small needle nose pliers to detach the third cable from motherboard.

Step 13

Use the iFixit Opening Tool to lift the back of the Vaio from the frame.
Slide the iFixit Opening Tool around the edges of the frame.

Use the iFixit Opening Tool to lift the back of the Vaio from the frame.

Slide the iFixit Opening Tool around the edges of the frame.

Step 14

Use the small needle nose pliers to pull the cable connector from the motherboard.
Push the flap to the side so you can access the screw beneath.
Use the #0PH screwdriver on the one 5.63mm screw.

Use the small needle nose pliers to pull the cable connector from the motherboard.

Push the flap to the side so you can access the screw beneath.

Use the #0PH screwdriver on the one 5.63mm screw.

Step 15

Unscrew the 5.63mm screw tethering the motherboard to the laptop with a #0PH screwdriver.
Remove the piece from the motherboard.

Unscrew the 5.63mm screw tethering the motherboard to the laptop with a #0PH screwdriver.

Remove the piece from the motherboard.

Step 16

Flip the motherboard upside down to access the other side.
Use a #0PH screwdriver to remove the three 3.61mm screws holding the fan to the motherboard.
Remove the fan from the motherboard.

Flip the motherboard upside down to access the other side.

Use a #0PH screwdriver to remove the three 3.61mm screws holding the fan to the motherboard.

Remove the fan from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Rachel Shrader

Member since: 01/31/2019

259 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Appalachian State University, Team S1-G1, Menagarishvili Spring 2019                        

                                                  Member of Appalachian State University, Team S1-G1, Menagarishvili Spring 2019 



                    APSU-MENAGARISHVILI-S19S1G1                     


                                            3 Members                     


                                            10 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team