Difficulty

Moderate

Steps

15

Time Required

                          15 - 20 minutes            

Sections

5

  • Battery
  • 3 steps
  • RAM Cover
  • 2 steps
  • Hard Drive
  • 2 steps
  • Back Cover
  • 4 steps
  • Optical Drive
  • 4 steps

Flags

0

  • BackSony Vaio VGN-FS640

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery               
  • Lay the closed laptop on its screen so the bottom is facing towards you.

Lay the closed laptop on its screen so the bottom is facing towards you.

1024

Step 2

  • Push both latches towards the center of the battery.

Push both latches towards the center of the battery.

Step 3

  • Revome the battery by pushing it away from the laptop.
  • Set the battery away from the laptop.

Revome the battery by pushing it away from the laptop.

Set the battery away from the laptop.

Step 4

              RAM Cover               
  • With the bottom of the laptop facing up, locate the RAM cover.
  • The RAM is covered by the panel with four columns of vents.
  • Locate the screw (Length: 4.8 mm) holding down the panel, which is near the edge of the laptop. Unscrew it with your phillips #0 screwdriver.

With the bottom of the laptop facing up, locate the RAM cover.

The RAM is covered by the panel with four columns of vents.

Locate the screw (Length: 4.8 mm) holding down the panel, which is near the edge of the laptop. Unscrew it with your phillips #0 screwdriver.

Step 5

  • Use your fingers to slide the cover away from the laptop. (It will only slide a few millimeters)
  • Once the panel is out of its locked position, it can be lifted out without any resistance.

Use your fingers to slide the cover away from the laptop. (It will only slide a few millimeters)

Once the panel is out of its locked position, it can be lifted out without any resistance.

Step 6

              Hard Drive               
  • Locate and remove the screw (Length: 7.7mm) for the hard drive cover.
  • Slide the cover until it is free from the laptop case.
  • Lift the cover to remove.

Locate and remove the screw (Length: 7.7mm) for the hard drive cover.

Slide the cover until it is free from the laptop case.

Lift the cover to remove.

Step 7

  • Locate and remove the four screws (Length: 7.7mm) holding the Hard Drive tray in place.
  • Using the tab on the tray, slide the Hard Drive away from the main body of the laptop.
  • The Hard Drive should now be disconnected.
  • Lift the drive out with the tab on the tray.

Locate and remove the four screws (Length: 7.7mm) holding the Hard Drive tray in place.

Using the tab on the tray, slide the Hard Drive away from the main body of the laptop.

The Hard Drive should now be disconnected.

Lift the drive out with the tab on the tray.

Step 8

              Back Cover               
  • Locate the screws highlighted here. There are 16 total.
  • Using a Phillips #0 screwdriver, remove the screws (Length: 6.8mm) and place them on a tray for later use.

Locate the screws highlighted here. There are 16 total.

Using a Phillips #0 screwdriver, remove the screws (Length: 6.8mm) and place them on a tray for later use.

Step 9

  • Before you proceed, make sure you pay special attention to the way the small plastic part that covers the radiator fins is held in place. You will need to know how it attaches when you reassemble the laptop.
  • You do not need to actually remove the part at this time. It is held in place by the rest of the back cover and will fall off when back cover is removed in the next step.

Before you proceed, make sure you pay special attention to the way the small plastic part that covers the radiator fins is held in place. You will need to know how it attaches when you reassemble the laptop.

You do not need to actually remove the part at this time. It is held in place by the rest of the back cover and will fall off when back cover is removed in the next step.

Step 10

  • After removing the screws, use your fingers to lift the back cover off the laptop.

After removing the screws, use your fingers to lift the back cover off the laptop.

Step 11

  • Remove the back cover and place it somewhere safe so you can locate it later.

Remove the back cover and place it somewhere safe so you can locate it later.

Step 12

              Optical Drive               
  • Locate and remove the screws (Length: 5.8mm) affixing the drive to the laptop frame.
  • Gently slide the drive away from the body of the laptop until it is disconnected.
  • Lift the drive out.

Locate and remove the screws (Length: 5.8mm) affixing the drive to the laptop frame.

Gently slide the drive away from the body of the laptop until it is disconnected.

Lift the drive out.

Step 13

  • Once the drive is removed from the main body of the laptop, you will need to remove the two connecting brackets.
  • Locate the screws for the brackets. There should be one on each side of the drive and two on the end that connects to the computer.
  • Unscrew and remove the brackets.

Once the drive is removed from the main body of the laptop, you will need to remove the two connecting brackets.

Locate the screws for the brackets. There should be one on each side of the drive and two on the end that connects to the computer.

Unscrew and remove the brackets.

Step 14

  • The last step is to remove the tray cover (the part that is exposed when the tray is closed).
  • The next two steps are not necessary if your replacement drive came with a tray cover already attached.
  • Open the drive by poking a straightened paper clip in the small hole on the front of the tray cover.

The last step is to remove the tray cover (the part that is exposed when the tray is closed).

The next two steps are not necessary if your replacement drive came with a tray cover already attached.

Open the drive by poking a straightened paper clip in the small hole on the front of the tray cover.

Step 15

  • Locate the two tabs on the inside of the cover that hold it in place.
  • Use a spudger or similar tool to unclip each tab. The cover should come right off.

Locate the two tabs on the inside of the cover that hold it in place.

Use a spudger or similar tool to unclip each tab. The cover should come right off.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             

Author

                                      with 5 other contributors 

                    Matt McCarty                     

Member since: 04/15/2010

220 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Team

                       Cal Poly, Team 24-32, Regan Spring 2010                        

                                                  Member of Cal Poly, Team 24-32, Regan Spring 2010 



                    CPSU-REGAN-S10S24G32                     


                                            4 Members                     


                                            16 Guides authored                     

Rock - Aug 10, 2017

Reply

To Clarify: Will the Vaio be usable w/o the optical drive once it has been reassembled?