Sony Vaio Tap 21 Svt212A11L Fan Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes

Sections

Screen
6 steps
Fan
4 steps

Flags

BackSony Vaio Tap 21
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Screen

Insert the plastic opening tool at an angle into the grill and lift the tab by applying force down and to the left as you are lifting it out of place.
Use your plastic opening tool to remove the right plastic tab blocking the screw mounts behind the device.
The plastic tab is located on a plastic stretch of grill running along the upper half of the back of the device.
You can find the tab looking for a solid fill within the grill. The tab is solid within the slits.

Insert the plastic opening tool at an angle into the grill and lift the tab by applying force down and to the left as you are lifting it out of place.

Use your plastic opening tool to remove the right plastic tab blocking the screw mounts behind the device.

The plastic tab is located on a plastic stretch of grill running along the upper half of the back of the device.

You can find the tab looking for a solid fill within the grill. The tab is solid within the slits.

1024

Step 2

Insert the plastic opening tool at an angle into the grill and lift the tab by applying force down and to the left as you are lifting it out of place.
Use your plastic opening tool to remove the right plastic tab blocking the screw mounts behind the device.
The plastic tab is located on a plastic stretch of grill running along the upper half of the back of the device.
You can find the tab looking for a solid fill within the grill. The tab is solid within the slits.

The plastic tab is located on a plastic stretch of grill running along the upper half of the back of the device.

Step 3

Remove the two 5mm screws on the back of the device using a JIS 0 screwdriver.

Remove the two 5mm screws on the back of the device using a JIS 0 screwdriver.

Step 4

Face the screen of the device upwards.
Gently un-clip the screen around the four sides of the body with the plastic opening tool.
Use an up-down motion.
It would be easier to do this if the device is fully rested flat by pushing the device down. It should rest on the stand.

Face the screen of the device upwards.

Gently un-clip the screen around the four sides of the body with the plastic opening tool.

Use an up-down motion.

It would be easier to do this if the device is fully rested flat by pushing the device down. It should rest on the stand.

Step 5

Lift the screen gently from the top of the device.
Make sure to lift the screen from the same side the screws were removed.

Lift the screen gently from the top of the device.

Make sure to lift the screen from the same side the screws were removed.

Step 6

Slowly and gently lay the screen on its face.
It’s important that the cables are not damaged while doing this process. Ensure as you lay the screen on its face any cables are carefully moved insuring no stress is applied on the cables.

Slowly and gently lay the screen on its face.

It’s important that the cables are not damaged while doing this process. Ensure as you lay the screen on its face any cables are carefully moved insuring no stress is applied on the cables.

Step 7

Fan

Remove four 9mm screws from the fan attachment located on the motherboard with a Phillips #1 screwdriver.

Remove four 9mm screws from the fan attachment located on the motherboard with a Phillips #1 screwdriver.

Step 8

Remove two 6mm screws located on both sides of the fan component using a Phillips #1 screwdriver.

Remove two 6mm screws located on both sides of the fan component using a Phillips #1 screwdriver.

Step 9

Un-click the cables attached to the face of the motherboard.
These cables are secured tight in their place so remove them with a firm grip.

Un-click the cables attached to the face of the motherboard.

These cables are secured tight in their place so remove them with a firm grip.

Step 10

Firmly lift the fan from the surface.
The fan is held tight in its place so lift it with slightly more force.

Firmly lift the fan from the surface.

The fan is held tight in its place so lift it with slightly more force.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor

                    Mauricio Retana

Member since: 10/02/2017

721 Reputation

                                      6 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team S4-G4, Livingston Fall 2017                        

                                                  Member of Cal Poly, Team S4-G4, Livingston Fall 2017 



                    CPSU-LIVINGSTON-F17S4G4                     


                                            4 Members                     


                                            12 Guides authored

Bill Scharf - Jun 16, 2019

Very nice guide. Thank you. Have you replaced the CPU yet in this model?

Introduction#

What you need#

Team#

Introduction

What you need

Team