Difficulty
Easy
Steps
11
Time Required
10 minutes
Sections
3
- Screen Assembly
- 3 steps
- Solid State Disk
- 3 steps
- Wifi Module
- 5 steps
Flags
2
Needs More Images
A few more images would make this guide’s procedures crystal clear.
Missing Details
Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.
BackSony Vaio Tap 11
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Screen Assembly
- Begin by opening the HDMI/USB port cover on the left edge.
- Remove the three #000 headed, 3 mm long screws located underneath the port cover.
Begin by opening the HDMI/USB port cover on the left edge.
Remove the three #000 headed, 3 mm long screws located underneath the port cover.
1024
Step 2
- Locate and open the Micro SD slot on the top side of the device.
- Remove the two screws located beneath the cover.
Locate and open the Micro SD slot on the top side of the device.
Remove the two screws located beneath the cover.
Step 3
- Attach the suction cup to the top right area of the screen.
- Pull to separate the screen from the rest of the device.
- Be aware of the front camera cable that is still connected to the rest of the device.
- Detach the display ribbon cable.
Attach the suction cup to the top right area of the screen.
Pull to separate the screen from the rest of the device.
Be aware of the front camera cable that is still connected to the rest of the device.
Detach the display ribbon cable.
Step 4
Solid State Disk
- Unplug the battery connector located beside the fan.
- Locate the SSD on the right side of the device, above the battery and beneath the WiFi chip.
Unplug the battery connector located beside the fan.
Locate the SSD on the right side of the device, above the battery and beneath the WiFi chip.
Step 5
- Remove the two 3 mm Phillips #000 screws from the right edge of the SSD.
Remove the two 3 mm Phillips #000 screws from the right edge of the SSD.
Step 6
- Pull the SSD towards the right and slightly up, removing it from the back assembly.
Pull the SSD towards the right and slightly up, removing it from the back assembly.
Step 7
Wifi Module
- Begin by removing the orange ribbon cable connecting the motherboard to the daughterboard, located above the SSD.
- Gently tug either side until it releases, then pull out the other end.
Begin by removing the orange ribbon cable connecting the motherboard to the daughterboard, located above the SSD.
Gently tug either side until it releases, then pull out the other end.
Step 8
- Remove the grey foam separator that was underneath the orange ribbon cable.
Remove the grey foam separator that was underneath the orange ribbon cable.
Step 9
- Remove the silver 3 mm Phillips screw that holds the WiFi module in place.
Remove the silver 3 mm Phillips screw that holds the WiFi module in place.
Step 10
- Remove the black and grey antenna cables from the right side of the device.
Remove the black and grey antenna cables from the right side of the device.
Step 11
- Remove module by gently pulling towards the right.
Remove module by gently pulling towards the right.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 2 other contributors
Alexander Bridges
Member since: 09/16/2015
1,217 Reputation
7 Guides authored
Badges:
17
+14 more badges
Team
IUPUI, Team 1-2, Harley Fall 2015
Member of IUPUI, Team 1-2, Harley Fall 2015
IUPUI-HARLEY-F15S1G2
4 Members
20 Guides authored