Sony Vaio Sve15112Fxs Fan Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          45 minutes

Sections

Fan
13 steps

Flags

BackSony Vaio SVE15112FXS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

Fan

Power laptop off before beginning.
Turn the laptop over so that it is positioned top down with the model number facing you.

Power laptop off before beginning.

Turn the laptop over so that it is positioned top down with the model number facing you.

1024

Step 2

Use a #0 Phillips screwdriver to remove the two 4.0 mm screws securing the hard drive cover.
To avoid losing any parts, we recommend that you place the loose screws on a magnetic project mat.

Use a #0 Phillips screwdriver to remove the two 4.0 mm screws securing the hard drive cover.

To avoid losing any parts, we recommend that you place the loose screws on a magnetic project mat.

Step 3

To expose the hard drive, remove the cover by sliding it toward you and pulling up on the panel.

To expose the hard drive, remove the cover by sliding it toward you and pulling up on the panel.

Step 4

Use a #0 Phillips screwdriver to remove the two 4.0 mm screws attaching the hard drive to the laptop.

Use a #0 Phillips screwdriver to remove the two 4.0 mm screws attaching the hard drive to the laptop.

Step 5

Pull the clear plastic ribbon to the left until the mount is detached from the laptop.
There will be some resistance as the hard drive is disconnected. If it does not move at all, check that all anchor screws are removed.
Lift the hard drive out of the well.

Pull the clear plastic ribbon to the left until the mount is detached from the laptop.

There will be some resistance as the hard drive is disconnected. If it does not move at all, check that all anchor screws are removed.

Lift the hard drive out of the well.

Step 6

Use a Phillips #0 screwdriver to remove the one 4.0 mm screw next to the model number label.

Use a Phillips #0 screwdriver to remove the one 4.0 mm screw next to the model number label.

Step 7

Use a plastic opening tool to slide the CD-ROM out from the laptop.

Use a plastic opening tool to slide the CD-ROM out from the laptop.

Step 8

Slide the “lock” tab upward to unlock the battery before removal.
While pushing the “release” tab upward, lift the battery and pull outward to remove it from the laptop.

Slide the “lock” tab upward to unlock the battery before removal.

While pushing the “release” tab upward, lift the battery and pull outward to remove it from the laptop.

Step 9

To unsecure the bottom cover, remove all the cover screws using a #0 Phillips screwdriver.
Remove the two 9.0 mm screws on each side of the battery.
Remove the twelve 8.0 mm long screws alongside the entire back cover.
Remove the three 3.0 mm screws inside the battery well.

To unsecure the bottom cover, remove all the cover screws using a #0 Phillips screwdriver.

Remove the two 9.0 mm screws on each side of the battery.

Remove the twelve 8.0 mm long screws alongside the entire back cover.

Remove the three 3.0 mm screws inside the battery well.

Step 10

Use a plastic opening tool to carefully pry open the latch points located under the silver plastic trim. Repeat this around the back cover.
It may be easiest to start around the CD-ROM bay because there is more room.
To avoid damaging the plastic trim and cover, do not force difficult areas and make sure the opening tool is completely under the black plastic cover, not just the silver trim.
Lift the back cover upward and away from the laptop.

Use a plastic opening tool to carefully pry open the latch points located under the silver plastic trim. Repeat this around the back cover.

It may be easiest to start around the CD-ROM bay because there is more room.

To avoid damaging the plastic trim and cover, do not force difficult areas and make sure the opening tool is completely under the black plastic cover, not just the silver trim.

Lift the back cover upward and away from the laptop.

Step 11

Use a Phillips #00 screwdriver to remove the three 3.0 mm screws attaching the fan to the heat sink unit.

Use a Phillips #00 screwdriver to remove the three 3.0 mm screws attaching the fan to the heat sink unit.

Step 12

Use a plastic opening tool to unsecure the white power cable connector.
Do not pull on the wires as this could rip them from the cable connector.
Carefully unwrap the red and yellow wires from the hooks.
Take note of how the wires are wrapped around the hooks.

Use a plastic opening tool to unsecure the white power cable connector.

Do not pull on the wires as this could rip them from the cable connector.

Carefully unwrap the red and yellow wires from the hooks.

Take note of how the wires are wrapped around the hooks.

Step 13

Lift the fan upward to remove it from the heat sink unit.

Lift the fan upward to remove it from the heat sink unit.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Ashley Bierman

Member since: 09/06/2018

1,169 Reputation

                                      5 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Ohio State, Team S1-G1, Whitney Fall 2018                        

                                                  Member of Ohio State, Team S1-G1, Whitney Fall 2018 



                    OSU-WHITNEY-F18S1G1                     


                                            2 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team