Difficulty
Moderate
Steps
11
Time Required
20 - 25 minutes
Sections
2
- Battery
- 4 steps
- SD Card Board
- 7 steps
Flags
0
BackSony Vaio PCG-4121GL
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the two 3mm Phillips #0 screws on the bottom of the computer that secure the plastic backing.
Remove the two 3mm Phillips #0 screws on the bottom of the computer that secure the plastic backing.
1024
Step 2
- Pull the bottom plate towards yourself until it unhinges fully.
- Once the plate is free from the backing remove it completely.
Pull the bottom plate towards yourself until it unhinges fully.
Once the plate is free from the backing remove it completely.
Step 3
- Look for the blue tab that is located to the bottom left of the battery.
Look for the blue tab that is located to the bottom left of the battery.
Step 4
- Pull the blue tab towards yourself until you hear a click.
- Once the blue tab is released, pull up on the battery.
- Once the battery can move freely, take it out completely.
- It may be helpful to have a spudger to make it easier to release the blue tab.
Pull the blue tab towards yourself until you hear a click.
Once the blue tab is released, pull up on the battery.
Once the battery can move freely, take it out completely.
It may be helpful to have a spudger to make it easier to release the blue tab.
Step 5
SD Card Board
- Remove seven 3mm Phillips #0 screws from the bottom of the computer.
- Remove eight 5mm Phillips #0 screws.
Remove seven 3mm Phillips #0 screws from the bottom of the computer.
Remove eight 5mm Phillips #0 screws.
Step 6
- Carefully remove the disk drive from its compartment.
Carefully remove the disk drive from its compartment.
Step 7
- Remove the three 2mm Phillips #00 screws located on the top right edge.
Remove the three 2mm Phillips #00 screws located on the top right edge.
Step 8
- Gently pull apart the top and bottom plastic bodies.
- Carefully remove the cable connectors.
- Slowly detach bottom component to avoid tearing wires/connectors.
Gently pull apart the top and bottom plastic bodies.
Carefully remove the cable connectors.
Slowly detach bottom component to avoid tearing wires/connectors.
Step 9
- Pull apart your device and set aside the screen of your laptop.
- Locate the SD Card Board in the bottom left of the computer body.
Pull apart your device and set aside the screen of your laptop.
Locate the SD Card Board in the bottom left of the computer body.
Step 10
- Remove the cables from their connectors.
- Do not apply too much force to the cable connectors or they may tear.
Remove the cables from their connectors.
Do not apply too much force to the cable connectors or they may tear.
Step 11
- Lightly press down on the bottom left corner of the plastic frame.
- Pull SD Board out towards you once it feels loose.
- Once the SD Board is free from the plastic, remove completely
- The SD Card slot is shown.
Lightly press down on the bottom left corner of the plastic frame.
Pull SD Board out towards you once it feels loose.
Once the SD Board is free from the plastic, remove completely
The SD Card slot is shown.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Bryce McNeil
Member since: 01/24/2019
376 Reputation
1 Guide authored
Badges:
9
+6 more badges
Team
Cal Poly, Team S2-G2, White Winter 2019
Member of Cal Poly, Team S2-G2, White Winter 2019
CPSU-WHITE-W19S2G2
4 Members
10 Guides authored