Difficulty

Moderate

Steps

15

Time Required

                          20 - 30 minutes

Sections

3

  • Battery
  • 4 steps
  • Hard Drive
  • 4 steps
  • Fan
  • 7 steps

Flags

1

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

  • BackSony Vaio PCG-3C2L

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Turn your computer over so the bottom is facing up.
  • The battery should be in the top on the back of the computer.

Turn your computer over so the bottom is facing up.

The battery should be in the top on the back of the computer.

1024

Step 2

  • Initially, the “lock” button should be pushed all the way to the left. To unlock the battery, move the lock button from the left to the right.

Initially, the “lock” button should be pushed all the way to the left. To unlock the battery, move the lock button from the left to the right.

Step 3

  • After unlocking the battery, hold the “release” button and push to the left.

After unlocking the battery, hold the “release” button and push to the left.

Step 4

  • Keep the “release” button pressed.
  • Use the iFixit opening tool (or your hands) to lift the battery up.

Keep the “release” button pressed.

Use the iFixit opening tool (or your hands) to lift the battery up.

Step 5

              Hard Drive
  • Place the laptop so that the bottom is facing up.

Place the laptop so that the bottom is facing up.

Step 6

  • Using a Phillips #0 screwdriver, remove the two 3.5mm screws on the hard drive cover.

Using a Phillips #0 screwdriver, remove the two 3.5mm screws on the hard drive cover.

Step 7

  • Using a Phillips #0 screwdriver, remove the three 8mm screws on the hard drive casing.
  • Remove the black hard drive casing by pulling it off.

Using a Phillips #0 screwdriver, remove the three 8mm screws on the hard drive casing.

Remove the black hard drive casing by pulling it off.

Step 8

  • Remove the hard drive by carefully sliding it out.

Remove the hard drive by carefully sliding it out.

Step 9

              Fan
  • Remove the six 8 mm edge screws from the back panel using a Phillips #0 screwdriver.
  • Remove the two 8 mm corner screws from the back panel using a Phillips #0 screwdriver.
  • Remove the four 8 mm middle screws from the back panel using a Phillips #0 screwdriver.
  • Remove the three 2 mm screws from the back panel using a Phillips #0 screwdriver.

Remove the six 8 mm edge screws from the back panel using a Phillips #0 screwdriver.

Remove the two 8 mm corner screws from the back panel using a Phillips #0 screwdriver.

Remove the four 8 mm middle screws from the back panel using a Phillips #0 screwdriver.

Remove the three 2 mm screws from the back panel using a Phillips #0 screwdriver.

Step 10

  • Remove the 6 mm screw from the battery holder using a Phillips #0 screwdriver.
  • Remove the two 4 mm screws from the battery holder using a Phillips #0 screwdriver.

Remove the 6 mm screw from the battery holder using a Phillips #0 screwdriver.

Remove the two 4 mm screws from the battery holder using a Phillips #0 screwdriver.

Step 11

  • Remove the CD cartridge from the back panel by sliding it out.

Remove the CD cartridge from the back panel by sliding it out.

Step 12

  • Using your hands, pull up the back panel about two inches up from the rest of the laptop.
  • Disconnect the black wire connector.
  • Remove back panel.
  • Pull up the back panel slowly so the black wire connector does not break.

Using your hands, pull up the back panel about two inches up from the rest of the laptop.

Disconnect the black wire connector.

Remove back panel.

Pull up the back panel slowly so the black wire connector does not break.

Step 13

  • Unscrew the four 4 mm captive screws from the fan casing using a Phillips #0 screwdriver.
  • Disconnect the black/red/yellow wire connector by gently pulling on the wire.
  • Remove the copper colored fan casing that contains the fan by pulling it off of the bottom of the laptop.

Unscrew the four 4 mm captive screws from the fan casing using a Phillips #0 screwdriver.

Disconnect the black/red/yellow wire connector by gently pulling on the wire.

Remove the copper colored fan casing that contains the fan by pulling it off of the bottom of the laptop.

Step 14

  • Remove the three 3 mm fan casing screws from the fan casing using a Phillips #0 screwdriver.

Remove the three 3 mm fan casing screws from the fan casing using a Phillips #0 screwdriver.

Step 15

  • Remove the fan from the fan casing by sliding it out.

Remove the fan from the fan casing by sliding it out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Jennifer Maier

Member since: 09/16/2019

152 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       Embry-Riddle Aeronautical University, Team S8-G3, Salas Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S8-G3, Salas Fall 2019 



                    ERAU-SALAS-F19S8G3                     


                                            4 Members                     


                                            12 Guides authored