Sony Srs Xb30 Wires Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          5 - 10 minutes

Sections

Battery
16 steps
Wires
2 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackSony SRS-XB30
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Battery

To remove the speaker grill, insert the big spudger underneath it in each corner.
Work around the edges to pry the grill up and off.

To remove the speaker grill, insert the big spudger underneath it in each corner.

Work around the edges to pry the grill up and off.

1024

Step 2

With the Sony logo facing towards you, use the medium spudger to lift the side plates from the internal frame.
This will need to be done on all four sides of the speaker to remove all four panels
This requires some effort because the adhesive is sticky.

With the Sony logo facing towards you, use the medium spudger to lift the side plates from the internal frame.

This will need to be done on all four sides of the speaker to remove all four panels

This requires some effort because the adhesive is sticky.

Step 3

Locate the four screws on the now exposed front panel.
Using the screwdriver with bit T7, unscrew each screw (15.0 mm long).

Locate the four screws on the now exposed front panel.

Using the screwdriver with bit T7, unscrew each screw (15.0 mm long).

Step 4

Next, remove the four outer edge screws, located on each corner of the speaker. The outer edge of the speaker is a clear plastic.
Use the same T7 screwdriver head here.
Remove each of the four corner screws (15.0 mm long).

Next, remove the four outer edge screws, located on each corner of the speaker. The outer edge of the speaker is a clear plastic.

Use the same T7 screwdriver head here.

Remove each of the four corner screws (15.0 mm long).

Step 5

With a little force, carefully lift the lid of the speaker.
Make sure that you do not pull on the wires.

With a little force, carefully lift the lid of the speaker.

Make sure that you do not pull on the wires.

Step 6

Unclip the four wire connectors (that are attached to the speaker lid).
Disconnect the thin yellow wire (attached to the speaker lid) from its port.

Unclip the four wire connectors (that are attached to the speaker lid).

Disconnect the thin yellow wire (attached to the speaker lid) from its port.

Step 7

Separate the speaker lid from the bottom frame.
To prepare the speaker for the next step place the lid parallel to the frame.

Separate the speaker lid from the bottom frame.

To prepare the speaker for the next step place the lid parallel to the frame.

Step 8

Locate the two silver screws (9 mm) attached to the two LED-light-chips on the speaker lid.
Using the screwdriver with bit PH1, unscrew each screw.

Locate the two silver screws (9 mm) attached to the two LED-light-chips on the speaker lid.

Using the screwdriver with bit PH1, unscrew each screw.

Step 9

Separate the speaker lid entirely from the bottom frame.

Separate the speaker lid entirely from the bottom frame.

Step 10

Remove the top screw (10 mm).
Use the screwdriver with bit T7.

Remove the top screw (10 mm).

Use the screwdriver with bit T7.

Step 11

Locate and remove the three black screws (10.0 mm) within the internal frame. Use bit T7.
There are two screws on the left side of the white box and one to its right.

Locate and remove the three black screws (10.0 mm) within the internal frame. Use bit T7.

There are two screws on the left side of the white box and one to its right.

Step 12

Slightly lift the white box with all the wires still attached.

Slightly lift the white box with all the wires still attached.

Step 13

Take the big spudger and pry the black casing up from the circuit box.

Take the big spudger and pry the black casing up from the circuit box.

Step 14

Locate the blue film attached to the circuit box containing the charging port.
Detach the blue film from the box.

Locate the blue film attached to the circuit box containing the charging port.

Detach the blue film from the box.

Step 15

Detach the yellow, black and red wires by pulling them directly up.

Detach the yellow, black and red wires by pulling them directly up.

Step 16

Insert the spudger along the battery edge and firmly hold the wires. Lift both sides up. The battery will pop out from its encasement.

Insert the spudger along the battery edge and firmly hold the wires. Lift both sides up. The battery will pop out from its encasement.

Step 17

              Wires

Locate the black, yellow, and red wires and steadily pull them smooth if they are tangled.

Locate the black, yellow, and red wires and steadily pull them smooth if they are tangled.

Step 18

Unravel any tangled wires or replace any damaged wires.
The wires should all run parallel to one another.

Unravel any tangled wires or replace any damaged wires.

The wires should all run parallel to one another.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Isabella Durazo

Member since: 04/09/2018

686 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Eastern Washington University, Team S3-G1, Rowley Spring 2018                        

                                                  Member of Eastern Washington University, Team S3-G1, Rowley Spring 2018 



                    EWU-ROWLEY-S18S3G1                     


                                            5 Members                     


                                            5 Guides authored

Better Introduction#

What you need#

Team#

Better Introduction

What you need

Team