Difficulty

Easy

Steps

12

Time Required

                          9 minutes

Sections

4

  • Battery
  • 3 steps
  • Speaker
  • 4 steps
  • Bluetooth
  • 3 steps
  • USB/AUX plug in
  • 2 steps

Flags

0

  • BackSony SRS-X5

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • To gain access to the 6 bottom screws remove the following. Remove the adhered 4 corner foam pads on the bottom of the speaker using the blue plastic opening tool to reveal the screws underneath. Remove the adhered 2 center plastic squares.
  • Make sure the speaker is unplugged and powered down before doing any work on the device.

To gain access to the 6 bottom screws remove the following. Remove the adhered 4 corner foam pads on the bottom of the speaker using the blue plastic opening tool to reveal the screws underneath. Remove the adhered 2 center plastic squares.

Make sure the speaker is unplugged and powered down before doing any work on the device.

1024

Step 2

  • Unscrew the six 6mm screws with a Phillips head #1 screwdriver.
  • Remove the bottom panel of the speaker.

Unscrew the six 6mm screws with a Phillips head #1 screwdriver.

Remove the bottom panel of the speaker.

Step 3

  • Unplug the battery by gently pinching the plastic end connected to the smaller board and pull away.
  • Remove the battery.

Unplug the battery by gently pinching the plastic end connected to the smaller board and pull away.

Remove the battery.

Step 4

              Speaker
  • To remove the speaker grill, first push down slightly on the 2 plastic hook tabs to release them, then push the middle plastic screw tab out.

To remove the speaker grill, first push down slightly on the 2 plastic hook tabs to release them, then push the middle plastic screw tab out.

Step 5

  • Remove the eight 0.5mm Phillips #1 screws from the speaker panel.

Remove the eight 0.5mm Phillips #1 screws from the speaker panel.

Step 6

  • Using the plastic opening tool, flip open the speaker panel.

Using the plastic opening tool, flip open the speaker panel.

Step 7

  • Unplug the 6-pin speaker connector and 2-pin microphone connector from the motherboard by squeezing the sides of the plastic ends.

Unplug the 6-pin speaker connector and 2-pin microphone connector from the motherboard by squeezing the sides of the plastic ends.

Step 8

              Bluetooth
  • Unplug the cord connected to the motherboard by squeezing the plastic sides.

Unplug the cord connected to the motherboard by squeezing the plastic sides.

Step 9

  • Gently tug on the plastic ribbon connected to the bottom side of the speaker to unplug it.

Gently tug on the plastic ribbon connected to the bottom side of the speaker to unplug it.

Step 10

  • Remove the motherboard.

Remove the motherboard.

Step 11

              USB/AUX plug in
  • Using the Phillips #1 screwdriver, remove the two 6mm screws holding the AUX board in place.

Using the Phillips #1 screwdriver, remove the two 6mm screws holding the AUX board in place.

Step 12

  • Remove the aux board. Be careful as the board might need some wiggling to get out.

Remove the aux board. Be careful as the board might need some wiggling to get out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Jeffrey Yalung

Member since: 09/28/2016

436 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Eastern Washington University, Team 2-6, Mathisen Fall 2016                        

                                                  Member of Eastern Washington University, Team 2-6, Mathisen Fall 2016 



                    EWU-MATHISEN-F16S2G6                     


                                            4 Members                     


                                            5 Guides authored

Khánh Trần - Mar 30, 2017

Reply

hi there, where can i buy aux board for replacement? thank you

Alan Castaneda - May 16, 2017

Reply

Donde puedo conseguir la tarjeta?