Sony Srs X2 Battery Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Face Plate
4 steps
Battery
2 steps

Flags

BackSONY SRS-X2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Face Plate

Use the metal spudger to pry the face screen open. Pull away from the device to remove.

Use the metal spudger to pry the face screen open. Pull away from the device to remove.

1024

Step 2

Remove seven, 27 mm long Phillips #1 screws.
Remove three, 11mm long Phillips #1 screws.
Remove four, 10 mm long Phillips#1 screws.

Remove seven, 27 mm long Phillips #1 screws.

Remove three, 11mm long Phillips #1 screws.

Remove four, 10 mm long Phillips#1 screws.

Step 3

Before removing the host plate, face the feet of the speaker to you. The wiring allows for minimal access to the inner components.
Use the spudger to remove the speaker host plate. Insert the metal tip in the seam between the host plate and the shell.
Be very careful when pulling the speaker host plate (described in the next step) as there are wiring connected to the host plate. This wiring is soldered to the plate and to the shell of the device. The wires are flexible and you can still open the device as shown in the second picture.
Center the spudger on the top of the device, this is furthest from the wiring, in wiggling the spudger under the plate, the plate should move up and out of the shell, you can finish lifting the plate away with your fingers.

Before removing the host plate, face the feet of the speaker to you. The wiring allows for minimal access to the inner components.

Use the spudger to remove the speaker host plate. Insert the metal tip in the seam between the host plate and the shell.

Be very careful when pulling the speaker host plate (described in the next step) as there are wiring connected to the host plate. This wiring is soldered to the plate and to the shell of the device. The wires are flexible and you can still open the device as shown in the second picture.

Center the spudger on the top of the device, this is furthest from the wiring, in wiggling the spudger under the plate, the plate should move up and out of the shell, you can finish lifting the plate away with your fingers.

Step 4

Be gentle when using the opening tool, wiggle the opening tool on each side of the socket to be sure the plastic does not snap.
Be careful not to damage the wires, pull from the plastic base to unplug.
Unplug the power cable connector shown using the plastic opening tool. Wiggle the tool under the lip of the plug, the smaller area and odd angle means lifting up with the plastic tool in the setup shown.
Unplug the power connector shown using the plastic opening tool lift from the front of the plug shown and move the opening tool to either side to get it all the way out of the socket.

Be gentle when using the opening tool, wiggle the opening tool on each side of the socket to be sure the plastic does not snap.

Be careful not to damage the wires, pull from the plastic base to unplug.

Unplug the power cable connector shown using the plastic opening tool. Wiggle the tool under the lip of the plug, the smaller area and odd angle means lifting up with the plastic tool in the setup shown.

Unplug the power connector shown using the plastic opening tool lift from the front of the plug shown and move the opening tool to either side to get it all the way out of the socket.

Step 5

              Battery

Remove the four, 11 mm, Phillips#1 screws on the battery cover plate.

Remove the four, 11 mm, Phillips#1 screws on the battery cover plate.

Step 6

Remove the battery cover plate carefully then proceed to remove the battery.

Remove the battery cover plate carefully then proceed to remove the battery.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      11 other people completed this guide.

Author

                                      with 2 other contributors

                    Yubei Wu

Member since: 10/04/2016

662 Reputation

                                      3 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       USF Tampa, Team 3-3, Sullivan Fall 2016                        

                                                  Member of USF Tampa, Team 3-3, Sullivan Fall 2016 



                    USFT-SULLIVAN-F16S3G3                     


                                            4 Members                     


                                            6 Guides authored

Ryan Lacharity - Jun 13, 2018

The top two red in the middle and the bottom two orange in the middle are reversed. Other than that the instructions are good.

Gustavo Crescente - Nov 26, 2019

THANKS! You are the best!

Mario Santos - Aug 5, 2021

Can anyone recommend an online store to buy a battery with the attached cable?

Introduction#

What you need#

Team#

Introduction

What you need

Team