Difficulty

Moderate

Steps

9

Time Required

                          20 minutes            

Sections

3

  • Battery
  • 4 steps
  • Motherboard
  • 4 steps
  • Speaker
  • 1 step

Flags

0

  • BackSony SRS-BTX500

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery               
  • Locate the four rubber grips on the bottom of the speaker. Use the plastic opening tool to remove the grips, exposing the underlying screws.

Locate the four rubber grips on the bottom of the speaker. Use the plastic opening tool to remove the grips, exposing the underlying screws.

1024

Step 2

  • Using a Phillips #1 screwdriver, remove the four 5mm screws that were underneath the four rubber grips.

Using a Phillips #1 screwdriver, remove the four 5mm screws that were underneath the four rubber grips.

Step 3

  • Use the plastic opening tool to run along the outside edges of the speaker. Pry along the seams until you can remove the side panel of the speaker, exposing the battery.

Use the plastic opening tool to run along the outside edges of the speaker. Pry along the seams until you can remove the side panel of the speaker, exposing the battery.

Step 4

  • Use the plastic opening tool to remove the battery from casing.
  • Unclasp the battery from the speaker. Remove and replace.

Use the plastic opening tool to remove the battery from casing.

Unclasp the battery from the speaker. Remove and replace.

Step 5

              Motherboard               
  • With the front of the speaker facing you, run the plastic opening tool along the bottom of the speaker. Then push the face of the speaker at both ends before lifting it off.

With the front of the speaker facing you, run the plastic opening tool along the bottom of the speaker. Then push the face of the speaker at both ends before lifting it off.

Step 6

  • Remove the two covers on the left and right with the small plastic opening tool to expose hidden screws.
  • Use a Phillips #1 screwdriver to remove the 14 indicated screws size 7mm.
  • Use a Phillips #1 screwdriver to remove the 8 indicated screws size 5mm.

Remove the two covers on the left and right with the small plastic opening tool to expose hidden screws.

Use a Phillips #1 screwdriver to remove the 14 indicated screws size 7mm.

Use a Phillips #1 screwdriver to remove the 8 indicated screws size 5mm.

Step 7

  • Lift off the casing on the left, right, and top of the speaker.

Lift off the casing on the left, right, and top of the speaker.

Step 8

  • Pull apart the speaker from the top. Unplug the indicated exposed wire that connects the speakers and the motherboard.
  • After the first wire is disconnected, separate the other connecting wires.

Pull apart the speaker from the top. Unplug the indicated exposed wire that connects the speakers and the motherboard.

After the first wire is disconnected, separate the other connecting wires.

Step 9

              Speaker               
  • Locate the broken speaker, and using a Philips #1 screwdriver, remove the four 7 mm screws to release the speaker from its position.
  • If replacing the center speaker, four additional 7 mm screws must be removed as indicated.
  • Replace it with the new speaker you have in your possession.

Locate the broken speaker, and using a Philips #1 screwdriver, remove the four 7 mm screws to release the speaker from its position.

If replacing the center speaker, four additional 7 mm screws must be removed as indicated.

Replace it with the new speaker you have in your possession.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 2 other contributors 

                    Sydney Legeer                     

Member since: 01/31/2016

239 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       University of Alabama, Team 1-5, Sydow campbell Spring 2016                        

                                                  Member of University of Alabama, Team 1-5, Sydow campbell Spring 2016 



                    UA-SYDOW CAMPBELL-S16S1G5                     


                                            3 Members                     


                                            2 Guides authored