Sony Slt Alpha 65V Viewfinder Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          10 - 15 minutes

Sections

Back Panel
5 steps
Motherboard
7 steps
Viewfinder
2 steps

Flags

BackSony SLT Alpha-65V
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Panel

Unscrew the four 4.0 mm Phillips #00 screws with a on the base of the camera below the the scheme that separates the front and back panels.
Unscrew the 5.0 mm Phillips #00 screw on the bottom right of the camera.

Unscrew the four 4.0 mm Phillips #00 screws with a on the base of the camera below the the scheme that separates the front and back panels.

Unscrew the 5.0 mm Phillips #00 screw on the bottom right of the camera.

1024

Step 2

Unscrew the 4.0 mm Phillips #00 screw on bottom of the left side of the camera.
Unscrew the 5.0 mm Phillips #00 screw near the top of the left side of the camera.

Unscrew the 4.0 mm Phillips #00 screw on bottom of the left side of the camera.

Unscrew the 5.0 mm Phillips #00 screw near the top of the left side of the camera.

Step 3

Be careful when pulling the back panel away as it will still be connected to the body of the camera by two strips of film.
When unscrewing the 5.0 mm screw on the dial, make sure to hold onto the dial that becomes detached after taking out the screw.
Unscrew the two 4.0 mm Phillips #00 screw at the top of the camera by the eyepiece.
Unscrew the 5.0 mm Phillips #00 screw of the dial below the other two screws.
Once all the screws are removed, carefully use your hands to detach the back panel from the camera. Working around the edges can help as well.

Be careful when pulling the back panel away as it will still be connected to the body of the camera by two strips of film.

When unscrewing the 5.0 mm screw on the dial, make sure to hold onto the dial that becomes detached after taking out the screw.

Unscrew the two 4.0 mm Phillips #00 screw at the top of the camera by the eyepiece.

Unscrew the 5.0 mm Phillips #00 screw of the dial below the other two screws.

Once all the screws are removed, carefully use your hands to detach the back panel from the camera. Working around the edges can help as well.

Step 4

Remove the two 4.0 mm Phillips #00 screws on the right of the camera that are located on the upper right side and under the “Remote” port flap.
Detach the right side panel with the remote and HDMI ports of the camera by gently pulling on the panel.

Remove the two 4.0 mm Phillips #00 screws on the right of the camera that are located on the upper right side and under the “Remote” port flap.

Detach the right side panel with the remote and HDMI ports of the camera by gently pulling on the panel.

Step 5

When the back panel is removed, be careful when moving the camera. There are parts inside the camera which now may come loose.
Use tweezers to remove the blue and orange ribbon connectors from their connection points pictured here.

When the back panel is removed, be careful when moving the camera. There are parts inside the camera which now may come loose.

Use tweezers to remove the blue and orange ribbon connectors from their connection points pictured here.

Step 6

              Motherboard

Remove the four 3.0 mm Phillips #00 screws.
Remove the 5.0 mm Phillips #00 screw.

Remove the four 3.0 mm Phillips #00 screws.

Remove the 5.0 mm Phillips #00 screw.

Step 7

Don’t forget to close these switches and lock the film back into place when reassembling the camera.
Use your finger to flip the switch that holds the dual ribbon connector in place.
Gently use tweezers to disconnect the dual ribbon connector and the thin blue ribbon connector to the right of it from the circuit board.

Don’t forget to close these switches and lock the film back into place when reassembling the camera.

Use your finger to flip the switch that holds the dual ribbon connector in place.

Gently use tweezers to disconnect the dual ribbon connector and the thin blue ribbon connector to the right of it from the circuit board.

Step 8

Use tweezers to disconnect the blue, gold, and brown ribbon connectors near the top of the camera.

Use tweezers to disconnect the blue, gold, and brown ribbon connectors near the top of the camera.

Step 9

Use a plastic opening tool to pop open the connector holding the next ribbon to the circuit board.
Use tweezers to disconnect the ribbon.

Use a plastic opening tool to pop open the connector holding the next ribbon to the circuit board.

Use tweezers to disconnect the ribbon.

Step 10

Use tweezers to unplug the blue adapter located at the top right of the circuit board.

Use tweezers to unplug the blue adapter located at the top right of the circuit board.

Step 11

Use either plastic opening tools or tweezers to unplug the white adapter located on the right side of the circuit board.

Use either plastic opening tools or tweezers to unplug the white adapter located on the right side of the circuit board.

Step 12

The circuit board will still be connected to the body of the camera by two pairs of cords.
Gently lift the circuit board away from the camera and turn it over.
Use tweezers to disconnect the final two plugs and completely remove the circuit board from the camera.

The circuit board will still be connected to the body of the camera by two pairs of cords.

Gently lift the circuit board away from the camera and turn it over.

Use tweezers to disconnect the final two plugs and completely remove the circuit board from the camera.

Step 13

              Viewfinder

The rotating dial on the right side of the eyepiece sensor is loosely connected and may fall out when removing the sensor.
Gently remove the eyepiece sensor from the viewfinder.

The rotating dial on the right side of the eyepiece sensor is loosely connected and may fall out when removing the sensor.

Gently remove the eyepiece sensor from the viewfinder.

Step 14

The viewfinder will pop out of its slot.
Gently remove the viewfinder from the camera.

The viewfinder will pop out of its slot.

Gently remove the viewfinder from the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Zhengjun Jiang

Member since: 04/28/2015

140 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Cal Poly, Team 14-11, Amido Spring 2015                        

                                                  Member of Cal Poly, Team 14-11, Amido Spring 2015 



                    CPSU-AMIDO-S15S14G11                     


                                            4 Members                     


                                            13 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team