Difficulty

Moderate

Steps

10

Time Required

Suggest a time??

Sections

4

  • Back Panel
  • 3 steps
  • Battery
  • 2 steps
  • Inner Casing
  • 2 steps
  • Motherboard
  • 3 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackSony Reader Touch Edition PRS-600

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Back Panel
  • Using the Phillips head screwdriver PH000, remove the two 1.4 mm screws that are located on the backside of the device.

Using the Phillips head screwdriver PH000, remove the two 1.4 mm screws that are located on the backside of the device.

1024

Step 2

  • Slide the back cover off by pushing it to the left, away from the side that held the screws.
  • Remove the cover.

Slide the back cover off by pushing it to the left, away from the side that held the screws.

Remove the cover.

Step 3

  • This is what the device should look like once the back cover panel has been removed.

This is what the device should look like once the back cover panel has been removed.

Step 4

              Battery
  • Once the back cover has been removed locate the battery in the bottom right corner of the device.
  • Using the pointed end of the spudger, push out the white plug that is connected to the battery from its beige base.

Once the back cover has been removed locate the battery in the bottom right corner of the device.

Using the pointed end of the spudger, push out the white plug that is connected to the battery from its beige base.

Step 5

  • Use the flat end of the spudger to pry the battery out of its holder. There may be glue holding it in place.

Use the flat end of the spudger to pry the battery out of its holder. There may be glue holding it in place.

Step 6

              Inner Casing
  • Using a screwdriver remove the four 1.4 mm screws that are holding the black plastic casing in place.

Using a screwdriver remove the four 1.4 mm screws that are holding the black plastic casing in place.

Step 7

  • Pry open the black casing to access the screw that is holding down the battery holder.
  • Remove the one 1.4 mm screw that is holding down the battery holder located under black casing.
  • Lift the black inner casing and the battery holder out of the device.
  • The battery holder and the black inner casing are connected by a thin strip of copper. There may be glue holding the black inner casing in place.

Pry open the black casing to access the screw that is holding down the battery holder.

Remove the one 1.4 mm screw that is holding down the battery holder located under black casing.

Lift the black inner casing and the battery holder out of the device.

The battery holder and the black inner casing are connected by a thin strip of copper. There may be glue holding the black inner casing in place.

Step 8

              Motherboard
  • Using a Phillips head screwdriver, remove the one 1.4 mm screw holding in the motherboard.

Using a Phillips head screwdriver, remove the one 1.4 mm screw holding in the motherboard.

Step 9

  • Using the flat end of the spudger, flip up the 4 latches holding down the thin, orange strips that connect the motherboard to the screen, audio/AC adapter/micro USB ports, and SD card/PRODuo ports.
  • To disconnect the the screen, audio/AC adapter/micro USB ports, and SD card/PRODuo ports pull each orange slip away from their corresponding latch.

Using the flat end of the spudger, flip up the 4 latches holding down the thin, orange strips that connect the motherboard to the screen, audio/AC adapter/micro USB ports, and SD card/PRODuo ports.

To disconnect the the screen, audio/AC adapter/micro USB ports, and SD card/PRODuo ports pull each orange slip away from their corresponding latch.

Step 10

  • Lift the end of the motherboard closest to the memory cards and pull out.

Lift the end of the motherboard closest to the memory cards and pull out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Terrika Ngobili

Member since: 10/13/2014

857 Reputation

                                      7 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Clemson, Team 1-4, Benson Fall 2014                        

                                                  Member of Clemson, Team 1-4, Benson Fall 2014 



                    CLEM-BENSON-F14S1G4                     


                                            4 Members                     


                                            22 Guides authored