Difficulty
Moderate
Steps
11
Time Required
Suggest a time??
Sections
2
- Sony Radio Model CFD S05 Prerequisite steps Replacement
- 5 steps
- Belt for the Tape Motor
- 6 steps
Flags
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
Better Introduction
Improve this guide by completing or revising its introduction.
BackSony Radio CFD-S05
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Sony Radio Model CFD S05 Prerequisite steps Replacement
- Unscrew the screws on the top of the radio.
Unscrew the screws on the top of the radio.
1024
Step 2
- Open the CD and cassette doors and remove the screws in the compartments.
- To open the CD door push on the bottom left corner of the CD door. To open the cassette door push the button that is to the left of the pause button.
Open the CD and cassette doors and remove the screws in the compartments.
To open the CD door push on the bottom left corner of the CD door. To open the cassette door push the button that is to the left of the pause button.
Step 3
- Flip the radio upside down and remove the battery cover. Unscrew the one screw below the batteries.
Flip the radio upside down and remove the battery cover. Unscrew the one screw below the batteries.
Step 4
- Remove the top of the radio enough to access the wires for removal.
- Do not forcefully remove the whole top piece of the radio! There will be wires connected to the top cover and circuit board.
Remove the top of the radio enough to access the wires for removal.
Do not forcefully remove the whole top piece of the radio! There will be wires connected to the top cover and circuit board.
Step 5
- Remove all of the wires that are connected to both the circuit board and the underside of the top of the radio by pulling them where they are connected
- This should include three sets of red and white wires, one set of white wires, one set of black wires, and two ribbon wires. Some cannot be disconnected from the top piece of the radio. Disconnect these plugs from the circuit board.
Remove all of the wires that are connected to both the circuit board and the underside of the top of the radio by pulling them where they are connected
This should include three sets of red and white wires, one set of white wires, one set of black wires, and two ribbon wires. Some cannot be disconnected from the top piece of the radio. Disconnect these plugs from the circuit board.
Step 6
Belt for the Tape Motor
- Locate the motor of the radio on the underside of the top of the radio.
Locate the motor of the radio on the underside of the top of the radio.
Step 7
- Unscrew the screw holding the motor to the top of the radio.
Unscrew the screw holding the motor to the top of the radio.
Step 8
- Lift up the motor.
- Don’t lift too high because the motor stand will break.
Lift up the motor.
Don’t lift too high because the motor stand will break.
Step 9
- Unhook the larger band from under the motor and remove it.
Unhook the larger band from under the motor and remove it.
Step 10
- Replace the band by hooking it beneath the motor.
Replace the band by hooking it beneath the motor.
Step 11
- Push the motor back down and screw it into place.
Push the motor back down and screw it into place.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 4 other contributors
Ian Nussman
Member since: 10/25/2013
959 Reputation
6 Guides authored
Badges:
11
+8 more badges
Team
UMass Dartmouth, Team 2-5, Gulbrandsen Fall 2013
Member of UMass Dartmouth, Team 2-5, Gulbrandsen Fall 2013
UMASSD-GULBRANDSEN-F13S2G5
2 Members
6 Guides authored
Carolyn Farley - Mar 23, 2017
Reply
I’m worried about removing wires. How do you put them back? Doesn’t that take some kind of special equipment/glue?