Difficulty
Moderate
Steps
11
Time Required
20 minutes
Sections
2
- Outer Casing
- 5 steps
- LCD Screen
- 6 steps
Flags
0
BackSony HDR-AS30V
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Outer Casing
- Power off the device. Remove the component jack cover.
- Open component door.
- Using the Phillips 00 screwdriver, remove the two screws holding the jack cover in place.
Power off the device. Remove the component jack cover.
Open component door.
Using the Phillips 00 screwdriver, remove the two screws holding the jack cover in place.
1024
Step 2
- Open the battery door.
- Slide the battery cap along the length of the camera, then flip the cap outward. Use caution; there may be internal damage affecting the functionality of the sliding mechanism.
Open the battery door.
Slide the battery cap along the length of the camera, then flip the cap outward. Use caution; there may be internal damage affecting the functionality of the sliding mechanism.
Step 3
- Prepare to remove outer casing.
- Using the 2.5 mm precision slotted screwdriver, insert the tip of the screwdriver under the holder to wedge. Use caution when preparing to wedge apart fragile components.
Prepare to remove outer casing.
Using the 2.5 mm precision slotted screwdriver, insert the tip of the screwdriver under the holder to wedge. Use caution when preparing to wedge apart fragile components.
Step 4
- Separate Casing from Device.
- With the screwdriver wedged, apply slight force while pulling the casing away from the device. Use caution to avoid causing damage to fragile parts.
Separate Casing from Device.
With the screwdriver wedged, apply slight force while pulling the casing away from the device. Use caution to avoid causing damage to fragile parts.
Step 5
- With the outer casing pulled away from the device, take note of the orientation of the inner component to avoid an electrical short.
- Once the orientation of the inner component is noted, slide the inner component out of the casing. You may now replace the broken casing with a new one.
With the outer casing pulled away from the device, take note of the orientation of the inner component to avoid an electrical short.
Once the orientation of the inner component is noted, slide the inner component out of the casing. You may now replace the broken casing with a new one.
Step 6
LCD Screen
- Remove two screws with the PH000 screwdriver.
- Pop off plastic holder.
Remove two screws with the PH000 screwdriver.
Pop off plastic holder.
Step 7
- With the flathead screwdriver, wedge under area shown and pop upwards.
- Be sure to move the flex cable out of the way while flipping the plastic inner casing upward.
With the flathead screwdriver, wedge under area shown and pop upwards.
Be sure to move the flex cable out of the way while flipping the plastic inner casing upward.
Step 8
- Gently push speaker out of slot
Gently push speaker out of slot
Step 9
- Flip open screen and make sure no cables are in the way.
Flip open screen and make sure no cables are in the way.
Step 10
- With the flathead, lift up cable lock and pull the film out from underneath the lock.
With the flathead, lift up cable lock and pull the film out from underneath the lock.
Step 11
- Gently pull out screen.
Gently pull out screen.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Dylan Keiter
Member since: 01/28/2015
101 Reputation
1 Guide authored
Badges:
3
Team
Penn State, Team 2-12, Kaschak Winter 2015
Member of Penn State, Team 2-12, Kaschak Winter 2015
PSU-KASCHAK-W15S2G12
4 Members
4 Guides authored
