Sony Handycam Hdr Cx380 Lens Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          2 minutes

Sections

Battery
3 steps
Camera Shell
7 steps
Lens Cover Panel
1 step
Shutter Assembly
5 steps
Lens
2 steps

Flags

BackSony Handycam HDR-CX380
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Rotate your camera such that the underside is facing you and the lens is facing the ground.
You should be able to see the camera’s label, and it should be rotated 90 degrees counterclockwise.

Rotate your camera such that the underside is facing you and the lens is facing the ground.

You should be able to see the camera’s label, and it should be rotated 90 degrees counterclockwise.

1024

Step 2

Using your left thumb, push down the slider to the left of the SD card slot.
When inserting a new battery or reinserting the one you removed, you can ignore this step.

Using your left thumb, push down the slider to the left of the SD card slot.

When inserting a new battery or reinserting the one you removed, you can ignore this step.

Step 3

Using your right index finger and thumb, pull the battery toward you and then away from the camera.

Using your right index finger and thumb, pull the battery toward you and then away from the camera.

Step 4

              Camera Shell

Orient the camera with the battery side facing up.

Orient the camera with the battery side facing up.

Step 5

Remove the single 4.5 mm Phillips #00 screw.
Remove the single 5.5 mm Phillips #00 screw.

Remove the single 4.5 mm Phillips #00 screw.

Remove the single 5.5 mm Phillips #00 screw.

Step 6

With the blue plastic opening tools, gently pry the plastic casing surrounding the start/stop button free.
Remove the casing using your right thumb and index finger.

With the blue plastic opening tools, gently pry the plastic casing surrounding the start/stop button free.

Remove the casing using your right thumb and index finger.

Step 7

Flip open the LCD panel to get to the side panel.
Remove the three 5.5 mm Phillips #00 screws.

Flip open the LCD panel to get to the side panel.

Remove the three 5.5 mm Phillips #00 screws.

Step 8

Turn the camera around to the grip side and remove the 5.5 mm Phillips Head screw using your J00 Phillips Head screwdriver.

Turn the camera around to the grip side and remove the 5.5 mm Phillips Head screw using your J00 Phillips Head screwdriver.

Step 9

With the bottom of the camera facing up, remove the two 5.5mm Phillips #00 screws.

With the bottom of the camera facing up, remove the two 5.5mm Phillips #00 screws.

Step 10

Orient the camera so the bottom is facing you.
Use the blue plastic opening tools to gently ease the camera shell off of the camera.
Rotate the camera so the LCD side panel is facing you and gently pry the shell off from the camera.

Orient the camera so the bottom is facing you.

Use the blue plastic opening tools to gently ease the camera shell off of the camera.

Rotate the camera so the LCD side panel is facing you and gently pry the shell off from the camera.

Step 11

              Lens Cover Panel

Orient the camera such that the lens is facing to your left.
Using your right hand to hold the camera, gently remove the lens panel from the camera with your left hand.
The camera should be oriented with the lens pointing to your left.

Orient the camera such that the lens is facing to your left.

Using your right hand to hold the camera, gently remove the lens panel from the camera with your left hand.

The camera should be oriented with the lens pointing to your left.

Step 12

              Shutter Assembly

Rotate the camera so that it is upright and the lens is pointed to your left.
Using your right hand to hold the screwdriver and your left to hold the camera, remove the single 5.5 mm Phillips #00 screw from on the top of the shutter assembly.

Rotate the camera so that it is upright and the lens is pointed to your left.

Using your right hand to hold the screwdriver and your left to hold the camera, remove the single 5.5 mm Phillips #00 screw from on the top of the shutter assembly.

Step 13

Rotate the camera such that the lens is pointed downward and the LCD screen points to your right.
Remove the two Phillips #00 screws from the LCD screen’s hinge.

Rotate the camera such that the lens is pointed downward and the LCD screen points to your right.

Remove the two Phillips #00 screws from the LCD screen’s hinge.

Step 14

Orient the camera such that it is upright and the lens is facing to your right.
Using your left hand to hold the camera, gently remove the shutter assembly from the hull with your right hand.
If you are only trying to remove the lens, you do not need to perform the next two steps.

Orient the camera such that it is upright and the lens is facing to your right.

Using your left hand to hold the camera, gently remove the shutter assembly from the hull with your right hand.

If you are only trying to remove the lens, you do not need to perform the next two steps.

Step 15

Orient the camera such that the bottom is facing toward you and the lens is facing to your right.
Using your metal tweezers, gently remove the wire harness connecting the shutter assembly to the motherboard.

Orient the camera such that the bottom is facing toward you and the lens is facing to your right.

Using your metal tweezers, gently remove the wire harness connecting the shutter assembly to the motherboard.

Step 16

Rotate the camera so that it is upright and the lens is facing to your right.
Remove the ribbon cable connecting the shutter assembly to the motherboard using your metal tweezers.
Be sure to pull the ribbon cable gently, as ribbon cables are easy to damage and can require soldering to repair.

Rotate the camera so that it is upright and the lens is facing to your right.

Remove the ribbon cable connecting the shutter assembly to the motherboard using your metal tweezers.

Be sure to pull the ribbon cable gently, as ribbon cables are easy to damage and can require soldering to repair.

Step 17

              Lens

Remove the three 5.5mm Phillips #00 screws holding the lens in.

Remove the three 5.5mm Phillips #00 screws holding the lens in.

Step 18

Gently pull the lens up from the camera.

Gently pull the lens up from the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Zackary Williams

Member since: 02/04/2016

457 Reputation

                                      3 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       USF Tampa, Team 16-5, Blackwell Winter 2016                        

                                                  Member of USF Tampa, Team 16-5, Blackwell Winter 2016 



                    USFT-BLACKWELL-W16S16G5                     


                                            3 Members                     


                                            16 Guides authored

Joseph m - Feb 10, 2021

Know where I can buy a replacement lense? Or have advice? Turned it one one day and it automatically gets stuck zoomed in and makes noises in the lense like it’s faulty

Introduction#

What you need#

Team#

Introduction

What you need

Team