Difficulty
Difficult
Steps
13
Time Required
50 minutes - 1 hour
Sections
4
- Battery
- 2 steps
- Camera’s Body
- 3 steps
- Lens
- 3 steps
- Motherboard
- 5 steps
Flags
0
BackSony Handycam HDR-CX220
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Push in the battery indicator.
Push in the battery indicator.
1024
Step 2
- Slide the battery out of the slot.
- To put the battery back in, line up the battery’s metal part with the camera’s and slide it in.
Slide the battery out of the slot.
To put the battery back in, line up the battery’s metal part with the camera’s and slide it in.
Step 3
Camera's Body
- Use the Phillips #0 screwdriver to remove the two 5mm screws.
- Use the Phillips #0 screwdriver to remove the two 5mm screws.
- Use the Phillips #0 screwdriver to remove the three 5mm screws.
Use the Phillips #0 screwdriver to remove the two 5mm screws.
Use the Phillips #0 screwdriver to remove the three 5mm screws.
Step 4
- Use the plastic opening tool to loosen the plastic case of the camcorder.
Use the plastic opening tool to loosen the plastic case of the camcorder.
Step 5
- Use your hands to remove the plastic case.
- Gently pull on the case not to damage anything internally.
Use your hands to remove the plastic case.
Gently pull on the case not to damage anything internally.
Step 6
Lens
- Use the Phillips #0 Screwdriver to remove the 5mm screw
- Use the Phillips #0 Screwdriver to remove the 5mm screw
- Use the Plastic Opening tools to unhook the highlighted area.
Use the Phillips #0 Screwdriver to remove the 5mm screw
Use the Plastic Opening tools to unhook the highlighted area.
Step 7
- Remove the 3 (4mm) screws on the front of the lens using the Philips #0 Screwdriver.
Remove the 3 (4mm) screws on the front of the lens using the Philips #0 Screwdriver.
Step 8
- Remove the lens and clean it if needed.
Remove the lens and clean it if needed.
Step 9
Motherboard
- Use the Phillips #0 Screwdriver to remove the shown 5mm screws.
- Use the plastic opening tool to release the front hook.
- Use the plastic opening tool to release the back hook.
Use the Phillips #0 Screwdriver to remove the shown 5mm screws.
Use the plastic opening tool to release the front hook.
Use the plastic opening tool to release the back hook.
Step 10
- Gently pull on the 2 wires shown on the bottom of the camcorder.
- Disconnect the wire shows on the second picture.
Gently pull on the 2 wires shown on the bottom of the camcorder.
Disconnect the wire shows on the second picture.
Step 11
- Use the Phillips #0 screwdriver to remove the 4mm screw shown.
- Gently remove the motherboard with your fingers.
Use the Phillips #0 screwdriver to remove the 4mm screw shown.
Gently remove the motherboard with your fingers.
Step 12
- Remove the side wire from the motherboard as shown on the photo.
- Remove the top wire from the motherboard as shown on the photo.
Remove the side wire from the motherboard as shown on the photo.
Remove the top wire from the motherboard as shown on the photo.
Step 13
- Unplug the speaker from the motherboard.
Unplug the speaker from the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Keven
Member since: 03/11/2016
811 Reputation
6 Guides authored
Badges:
11
+8 more badges
Team
UMass Dartmouth, Team 8-5, Botvin Spring 2016
Member of UMass Dartmouth, Team 8-5, Botvin Spring 2016
UMASSD-BOTVIN-S16S8G5
3 Members
12 Guides authored
