Difficulty
Moderate
Steps
10
Time Required
15 - 45 minutes
Sections
2
- Panel
- 8 steps
- Speaker
- 2 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackSony Handycam FDR-AX33
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Panel
- Remove the battery by pushing the latch towards the body of the camera. Push the battery down and pull it out.
- Remove the six black 4 mm Phillips #00 screws from the bottom panel of the camera.
- Pull off the bottom panel. It may be difficult, but tugging on it shouldn’t cause harm to yourself or the device.
- Be sure to un-velcro the handle strap.
Remove the battery by pushing the latch towards the body of the camera. Push the battery down and pull it out.
Remove the six black 4 mm Phillips #00 screws from the bottom panel of the camera.
Pull off the bottom panel. It may be difficult, but tugging on it shouldn’t cause harm to yourself or the device.
Be sure to un-velcro the handle strap.
1024
Step 2
- Remove the 3 mm Phillips #00 screw from the bottom of the camera.
- Remove the 4 mm Phillips #00 screw from the right panel.
- Pull the right panel off. Again, it might be difficult, but pulling hard shouldn’t harm you or the camera.
- You may have to use the opening tool to remove this panel.
Remove the 3 mm Phillips #00 screw from the bottom of the camera.
Remove the 4 mm Phillips #00 screw from the right panel.
Pull the right panel off. Again, it might be difficult, but pulling hard shouldn’t harm you or the camera.
You may have to use the opening tool to remove this panel.
Step 3
- Remove the two 4 mm Phillips #00 screws from the top right corner of the camera.
- Remove the 4 mm Phillips #00 screw from in front of the flash mount.
Remove the two 4 mm Phillips #00 screws from the top right corner of the camera.
Remove the 4 mm Phillips #00 screw from in front of the flash mount.
Step 4
- Remove the 3 mm Phillips #00 screw from below the right side of the battery slot.
- Remove the black 5 mm Phillips #00 screw from the top of the battery slot.
Remove the 3 mm Phillips #00 screw from below the right side of the battery slot.
Remove the black 5 mm Phillips #00 screw from the top of the battery slot.
Step 5
- Remove the three 4 mm Phillips #00 screws from the left panel underneath the display screen.
- You’ll need to extend the eyepiece by pulling it out from the body of the camera.
- Pull the top panel off of the device with the iFixit opening tool.
Remove the three 4 mm Phillips #00 screws from the left panel underneath the display screen.
You’ll need to extend the eyepiece by pulling it out from the body of the camera.
Pull the top panel off of the device with the iFixit opening tool.
Step 6
- Remove the top and bottom 4 mm Phillips #00 screws from the display screen hinge.
- Use the iFixit opening tool to remove the screen hinge.
Remove the top and bottom 4 mm Phillips #00 screws from the display screen hinge.
Use the iFixit opening tool to remove the screen hinge.
Step 7
- Remove the 3 mm Phillips #00 screw from between the eyepiece and the panel directly to the right of the battery slot.
- Angle the eyepiece up to reach the screw with the screwdriver.
- Take the panel directly to the right of the battery slot off of the camera.
Remove the 3 mm Phillips #00 screw from between the eyepiece and the panel directly to the right of the battery slot.
Angle the eyepiece up to reach the screw with the screwdriver.
Take the panel directly to the right of the battery slot off of the camera.
Step 8
- Remove the 4 mm Phillips #00 screw above and to the right of the battery slot.
- Pry the left panel out at an angle by pushing the plastic slat between the battery slot and the eyepiece.
- Wiggle the left panel and pull it out gently.
- The left panel can be hard to remove so make sure to apply a good amount of force, but be cautious to not harm yourself or the device.
Remove the 4 mm Phillips #00 screw above and to the right of the battery slot.
Pry the left panel out at an angle by pushing the plastic slat between the battery slot and the eyepiece.
Wiggle the left panel and pull it out gently.
The left panel can be hard to remove so make sure to apply a good amount of force, but be cautious to not harm yourself or the device.
Step 9
Speaker
- Remove the two 4 mm Phillips #00 screws from the inside of the screen hinge.
- Remove the black plastic from the back of the screen.
Remove the two 4 mm Phillips #00 screws from the inside of the screen hinge.
Remove the black plastic from the back of the screen.
Step 10
- Using the tweezers, unplug the speaker. The connector should be a white piece of plastic attached to a red wire and a black wire.
- Remove the speaker with the black nylon spudger. The speaker is attached by adhesive.
Using the tweezers, unplug the speaker. The connector should be a white piece of plastic attached to a red wire and a black wire.
Remove the speaker with the black nylon spudger. The speaker is attached by adhesive.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Lee Conway
Member since: 01/24/2019
184 Reputation
2 Guides authored
Badges:
4
+1 more badge
Team
Cal Poly, Team S18-G2, White Winter 2019
Member of Cal Poly, Team S18-G2, White Winter 2019
CPSU-WHITE-W19S18G2
4 Members
12 Guides authored
