Difficulty
Moderate
Steps
11
Time Required
Suggest a time??
Sections
2
- Hard DRive
- 5 steps
- LCD Screen
- 6 steps
Flags
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
BackSony Handycam DCR-SR 47
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Hard DRive
- Remove the battery.
- Use Philips #000 screwdriver to remove the 3mm screw under the battery
- *It is recommended that you wait One Hour after removing the battery before disassembling the rest of the camera
Remove the battery.
Use Philips #000 screwdriver to remove the 3mm screw under the battery
*It is recommended that you wait One Hour after removing the battery before disassembling the rest of the camera
1024
Step 2
- Using the Phillips #000 screwdriver, remove all 6 of the 3mm screws located on the side of the camera.
- This step seems unnecessary to initially find the Hard Drive, but will allow access to the attached flex cable
Using the Phillips #000 screwdriver, remove all 6 of the 3mm screws located on the side of the camera.
This step seems unnecessary to initially find the Hard Drive, but will allow access to the attached flex cable
Step 3
- Using the Phillips #000 tool, remove the three 3mm screws from under the LCD screen
Using the Phillips #000 tool, remove the three 3mm screws from under the LCD screen
Step 4
- Using the Phillips #000 screwdriver, remove the one 3mm screw on the back of the camera
- Pull away the back shell of the camera, exposing the hard drive.
Using the Phillips #000 screwdriver, remove the one 3mm screw on the back of the camera
Pull away the back shell of the camera, exposing the hard drive.
Step 5
- Gently pull the flex cable away from the hard drive. It should pop-off with minimal effort.
- The black guard has been removed in the first picture. The guard does not need to be removed in order to reach hard drive and cable, but it does show the path that the cable takes
- Once removing the flex cable, remove the plastic guard from the side of the hard drive.
Gently pull the flex cable away from the hard drive. It should pop-off with minimal effort.
The black guard has been removed in the first picture. The guard does not need to be removed in order to reach hard drive and cable, but it does show the path that the cable takes
Once removing the flex cable, remove the plastic guard from the side of the hard drive.
Step 6
LCD Screen
- Insert wisdom here.
Insert wisdom here.
Step 7
Step 8
- Using the plastic opening tool, separate the LCD screen from its plastic housing
Using the plastic opening tool, separate the LCD screen from its plastic housing
Step 9
- Using the spudger, or by gently pulling, remove the smaller end of the flex cable from the LCD Screen
Using the spudger, or by gently pulling, remove the smaller end of the flex cable from the LCD Screen
Step 10
- Using the Phillips #000 Screwdriver, remove the one 3mm screw from the LCD Scren
- The LCD screen may now be removed from the camera completely.
Using the Phillips #000 Screwdriver, remove the one 3mm screw from the LCD Scren
The LCD screen may now be removed from the camera completely.
Step 11
- Take the LCD screen away from the housing and replace with new screen
Take the LCD screen away from the housing and replace with new screen
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Ragan Whitlock
Member since: 08/26/2015
532 Reputation
4 Guides authored
Badges:
13
+10 more badges
Team
Western Carolina University, Team 1-2, Virtue Fall 2015
Member of Western Carolina University, Team 1-2, Virtue Fall 2015
WCU-VIRTUE-F15S1G2
4 Members
8 Guides authored
Triforce Studios - Feb 7, 2017
Reply
where can i buy a screen for this camera?