Difficulty

Moderate

Steps

12

Time Required

                          5 - 10 minutes

Sections

6

  • Back Phone Cover
  • 1 step
  • Battery
  • 1 step
  • Front Phone Cover
  • 1 step
  • Front Dark Grey Case
  • 3 steps
  • Screens
  • 5 steps
  • Front Speaker
  • 1 step

Flags

1

Missed a Step

Oops! This guide is currently missing some important steps.

  • BackSony Ericsson z300

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Phone Cover
  • To remove the back cover, use your thumb to press down on the center of case and slide it off.

To remove the back cover, use your thumb to press down on the center of case and slide it off.

1024

Step 2

              Battery
  • Using a fingernail lift the battery out of the phone.

Using a fingernail lift the battery out of the phone.

Step 3

              Front Phone Cover
  • To remove the front cover, lift up the case with a fingernail in the small slot as shown.

To remove the front cover, lift up the case with a fingernail in the small slot as shown.

Step 4

              Front Dark Grey Case
  • To remove the front grey case, remove the two screws shown with a T5 Torx Screwdriver.

To remove the front grey case, remove the two screws shown with a T5 Torx Screwdriver.

Step 5

  • Pry up the dark grey case with your fingernail until all four snaps around the top are loose.

Pry up the dark grey case with your fingernail until all four snaps around the top are loose.

Step 6

  • Lift up towards the bottom and slide the case off.

Lift up towards the bottom and slide the case off.

Step 7

              Screens
  • Use a plastic opening tool to lift the black tape off of the ribbon cable connector.

Use a plastic opening tool to lift the black tape off of the ribbon cable connector.

Step 8

  • Lift the ribbon cable connector lock using a plastic opening tool.

Lift the ribbon cable connector lock using a plastic opening tool.

Step 9

  • Slide the black ribbon cable tray out with a plastic opening tool.
  • Shown in the second picture is the try already slid out.

Slide the black ribbon cable tray out with a plastic opening tool.

Shown in the second picture is the try already slid out.

Step 10

  • Slide the ribbon cable out of the connector.
  • Shown in the second picture is the cable already out.

Slide the ribbon cable out of the connector.

Shown in the second picture is the cable already out.

Step 11

  • Use a plastic opening tool to lift up on the screen board and release the clips holding it in place.
  • Lift the entire board out of the phone to remove both screens.

Use a plastic opening tool to lift up on the screen board and release the clips holding it in place.

Lift the entire board out of the phone to remove both screens.

Step 12

              Front Speaker
  • Use a plastic opening tool to lift the speaker out of its circular slot.

Use a plastic opening tool to lift the speaker out of its circular slot.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Alex Serventi

Member since: 10/07/2010

65 Reputation

                                      13 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 5-15, Maness Fall 2010                        

                                                  Member of Cal Poly, Team 5-15, Maness Fall 2010 



                    CPSU-MANESS-F10S5G15                     


                                            4 Members                     


                                            26 Guides authored