Difficulty
Moderate
Steps
12
Time Required
30 minutes - 1 hour
Sections
1
- Glass Screen
- 12 steps
Flags
2
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
Better Introduction
Improve this guide by completing or revising its introduction.
BackSony Ericsson Xperia X10
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Glass Screen
- Remove the back cover and the battery.
Remove the back cover and the battery.
1024
Step 2
- Remove the eight 5mm T6 screws from the back of the phone.
Remove the eight 5mm T6 screws from the back of the phone.
Step 3
- Use a case opening tool to release clips holding the case together.
- It’s easier to start at the bottom right side of the phone. Insert the tool and run it down the side of the phone, using a prying motion to pull it apart.
Use a case opening tool to release clips holding the case together.
It’s easier to start at the bottom right side of the phone. Insert the tool and run it down the side of the phone, using a prying motion to pull it apart.
Step 4
- Take the part on the left side and put it out of the way.
Take the part on the left side and put it out of the way.
Step 5
- Insert a flat head screw driver under the two clips and pry up.
- The chip should come loose with just a ribbon cable holding it to the rest of the phone.
Insert a flat head screw driver under the two clips and pry up.
The chip should come loose with just a ribbon cable holding it to the rest of the phone.
Step 6
- Using a flat head screwdriver, flip the chip to the left and remove the ribbon cable.
Using a flat head screwdriver, flip the chip to the left and remove the ribbon cable.
Step 7
- Remove the volume and camera buttons. Using your fingers or a screwdriver, pull off the black plastic piece on the very top of the phone.
Remove the volume and camera buttons. Using your fingers or a screwdriver, pull off the black plastic piece on the very top of the phone.
Step 8
- Using a flat head screw driver, undo the ribbon cables connected to the phone.
Using a flat head screw driver, undo the ribbon cables connected to the phone.
Step 9
- Gently insert a flat head screw driver under the logic board and pry to remove it from the phone casing.
Gently insert a flat head screw driver under the logic board and pry to remove it from the phone casing.
Step 10
- Remove the logic board and put it to the side.
Remove the logic board and put it to the side.
Step 11
- Using a flat head screw driver, disconnect the glue holding the left ribbon cable to the phone. Pull up the black plastic piece being pointed to in the image.
Using a flat head screw driver, disconnect the glue holding the left ribbon cable to the phone. Pull up the black plastic piece being pointed to in the image.
Step 12
- Using a flat head screwdriver, pry up the board.
- Remove the power button from the top of the phone.
Using a flat head screwdriver, pry up the board.
Remove the power button from the top of the phone.
To reassemble your device, follow these instructions in reverse order. The pieces need to be placed exactly back into the phone as they came out or else they won’t fit together correctly.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Matt
Member since: 10/29/2013
319 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
UMass Dartmouth, Team 1-5, Shastany Fall 2013
Member of UMass Dartmouth, Team 1-5, Shastany Fall 2013
UMASSD-SHASTANY-F13S1G5
2 Members
3 Guides authored
djidja - Jan 3, 2015
Reply
good evening
when I put my SD card in my xperia it not appear but when I place it in another mobile standard market