Difficulty
Moderate
Steps
8
Time Required
15 minutes
Sections
1
- Main Screen
- 8 steps
Flags
0
BackSony Ericsson W300i
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Main Screen
- Here is the phone in question: The Sony Ericsson W300i.
- To access the interior of the phone, you need the a plastic opening tool, and a T6 Torx screwdriver.
Here is the phone in question: The Sony Ericsson W300i.
To access the interior of the phone, you need the a plastic opening tool, and a T6 Torx screwdriver.
1024
Step 2
- Before removing the screen, you must first remove the battery.
- Remove the battery cover by applying pressure while sliding the base cover away from the phone and then lifting the cover up.
Before removing the screen, you must first remove the battery.
Remove the battery cover by applying pressure while sliding the base cover away from the phone and then lifting the cover up.
Step 3
- Using your fingers, lift the end of the battery up and then pry the battery from the phone base.
- During reassembly you must reinsert the battery so the gold markings are at the top of the battery.
Using your fingers, lift the end of the battery up and then pry the battery from the phone base.
During reassembly you must reinsert the battery so the gold markings are at the top of the battery.
Step 4
- This step may take a few minutes.
- Remove the front plate off the phone with a plastic opening tool to gain access to the screws beneath.
- Use the point indicated on the photo as a good prying point.
- Use a moderate amount of force.
- Be aware of the sharp edges of the prying tool.
This step may take a few minutes.
Remove the front plate off the phone with a plastic opening tool to gain access to the screws beneath.
Use the point indicated on the photo as a good prying point.
Use a moderate amount of force.
Be aware of the sharp edges of the prying tool.
Step 5
- Use the T6 Torx screwdriver to remove the four screws.
- Place screws in a safe location to avoid losing them.
Use the T6 Torx screwdriver to remove the four screws.
Place screws in a safe location to avoid losing them.
Step 6
- This step may take a few minutes.
- Use a plastic opening tool to separate the screen cover from the top half of the phone.
- Slide the corner of the opening tool along the side of the phone toward the bottom corner.
- With the phone screen facing away from you, press into the screen crevice at an angle so that the tool pushes away towards the main screen.
- Use a moderate amount of force.
- Be aware of the sharp edges of the prying tool.
- Once the seal has been broken, tug the cover away.
Use a plastic opening tool to separate the screen cover from the top half of the phone.
Slide the corner of the opening tool along the side of the phone toward the bottom corner.
With the phone screen facing away from you, press into the screen crevice at an angle so that the tool pushes away towards the main screen.
Once the seal has been broken, tug the cover away.
Step 7
- Use your fingers to pry the plug end of the orange ribbon cable away from the screen.
- Remove screen.
Use your fingers to pry the plug end of the orange ribbon cable away from the screen.
Remove screen.
Step 8
- Using the new screen, reattach the plug end of the orange ribbon cable.
- Push new screen into the phone.
Using the new screen, reattach the plug end of the orange ribbon cable.
Push new screen into the phone.
Reassemble the phone following the steps in reverse.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 6 other contributors
Michael Faist
Member since: 02/17/2016
163 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
Ohio State, Team 1-2, Garvin Spring 2016
Member of Ohio State, Team 1-2, Garvin Spring 2016
OSU-GARVIN-S16S1G2
3 Members
4 Guides authored