Sony Dvp Sr200P Processing Board Replacement Repair Guide

Difficulty

Moderate

Steps

6

Time Required

                          10 minutes            

Sections

2

• Top Cover
• 2 steps
• Processing Board
• 4 steps

Flags

3

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Better Introduction

Improve this guide by completing or revising its introduction.

• BackSony DVP-SR200P

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Top Cover               

• Remove the five #1 Phillips screws (black, 3/16") attaching the cover to the DVD player.
• One 3/16" screw on the right side of the DVD player.
• One 3/16" screw on the left side of the DVD player (directly opposite of other screw).
• Three 3/16" screws on the back of the DVD player.

Remove the five #1 Phillips screws (black, 3/16") attaching the cover to the DVD player.

One 3/16" screw on the right side of the DVD player.

One 3/16" screw on the left side of the DVD player (directly opposite of other screw).

Three 3/16" screws on the back of the DVD player.

1024

Step 2

• Slide the cover away from the front of the DVD player until it is off.

Slide the cover away from the front of the DVD player until it is off.

Step 3

              Processing Board               

• Remove the blue tape from the processing board by gently pulling upward.

Remove the blue tape from the processing board by gently pulling upward.

Step 4

• Use the tweezers to remove the four sets of wires connected to the processing board. Start with the cord located in front of the row of three cords.
• The wires may be difficult to remove. Wiggling them while lifting them up may help remove them.

Use the tweezers to remove the four sets of wires connected to the processing board. Start with the cord located in front of the row of three cords.

The wires may be difficult to remove. Wiggling them while lifting them up may help remove them.

Step 5

• Handle the processing board with care. It is fragile.
• Unscrew the two #1 Phillips screws (silver, 3/16") located on the two edge corners of the processing board.

Handle the processing board with care. It is fragile.

Unscrew the two #1 Phillips screws (silver, 3/16") located on the two edge corners of the processing board.

Step 6

• Orient the DVD player so that you are facing the video and audio jacks.
• Unscrew the two #1 Phillips screws (silver, 3/16") located on the outside of the DVD player
• The processing board is now free to be removed and replaced.

Orient the DVD player so that you are facing the video and audio jacks.

Unscrew the two #1 Phillips screws (silver, 3/16") located on the outside of the DVD player

The processing board is now free to be removed and replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 7 other contributors 

                    Brian Hua                     

Member since: 01/11/2013

74 Reputation

                                      3 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Team

                       Cal Poly, Team 5-17, Forte Winter 2013                        

                                                  Member of Cal Poly, Team 5-17, Forte Winter 2013 



                    CPSU-FORTE-W13S5G17                     


                                            5 Members                     


                                            6 Guides authored                     

Dhiraj Vasave - Dec 26, 2016

Reply

I have Sony DVD player dvp at510p. After switching it runs then automatic Power go down while running it’s process ic get hotter and hotter what’s the right solutions plz help me

SO my DVD player run 5to 6 minutes then automatic stop all power goes to less