Difficulty
Moderate
Steps
17
Time Required
30 minutes
Sections
4
- Back Cover
- 6 steps
- Screen
- 3 steps
- SD Card Holder
- 6 steps
- SD Motherboard
- 2 steps
Flags
0
BackSony DSC-RX100MA Model IV
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Back Cover
- Remove battery by sliding the tab to open the cover
Remove battery by sliding the tab to open the cover
1024
Step 2
- Using the screwdriver, remove all screws (black 2.5mm) from outermost layer of the assembly.
- All screws in the camera can be removed with the PH 0 driver head.
Using the screwdriver, remove all screws (black 2.5mm) from outermost layer of the assembly.
All screws in the camera can be removed with the PH 0 driver head.
Step 3
- Also using the screwdriver, remove screws (black 1mm) underneath articulated LCD screen.
- Remove the marked 2.5 mm screws with the screwdriver
Also using the screwdriver, remove screws (black 1mm) underneath articulated LCD screen.
Remove the marked 2.5 mm screws with the screwdriver
Step 4
- Using the plastic opening tools, carefully pry off the bottom plate.
- Do not pull too hard as you may break the plastic casing.
Using the plastic opening tools, carefully pry off the bottom plate.
Do not pull too hard as you may break the plastic casing.
Step 5
- Using the same plastic opening tools, separate the screen and back assembly from the front portion of the camera
- Once the back assembly is slightly detached, pull the media covers for the HDMI and Multimedia ports
Using the same plastic opening tools, separate the screen and back assembly from the front portion of the camera
Once the back assembly is slightly detached, pull the media covers for the HDMI and Multimedia ports
Step 6
- Remove the back cover
Remove the back cover
Step 7
Screen
- Move side panel to get access to screws
- Remove two screws (black 2.5mm) with PH #0 screwdriver
Move side panel to get access to screws
Remove two screws (black 2.5mm) with PH #0 screwdriver
Step 8
- Remove back panel assembly while still keeping ribbon cable attached
- Be very gentle and care not to tear the gold ribbon cable. This will be a common theme throughout these replacement guides.
Remove back panel assembly while still keeping ribbon cable attached
Be very gentle and care not to tear the gold ribbon cable. This will be a common theme throughout these replacement guides.
Step 9
- Carefully unplug ribbon connector to fully detach LCD screen assembly from camera
Carefully unplug ribbon connector to fully detach LCD screen assembly from camera
Step 10
SD Card Holder
- Remove remaining screw which holds the copper casing in the camera
Remove remaining screw which holds the copper casing in the camera
Step 11
- Using the plastic opening tools, carefully pry off the copper casing at the two pictured points.
- Remove casing
Using the plastic opening tools, carefully pry off the copper casing at the two pictured points.
Remove casing
Step 12
- Using Philips Screwdriver, remove the four screws as marked on the picture
Using Philips Screwdriver, remove the four screws as marked on the picture
Step 13
- Place your finger into the battery port and push up on the SD card holder to push it out of its socket.
- Give it a little wiggle and you should feel the SD card holder come out.
Place your finger into the battery port and push up on the SD card holder to push it out of its socket.
Give it a little wiggle and you should feel the SD card holder come out.
Step 14
- Carefully remove the gold ribbons from the ports of the motherboard by lifting the gray tabs and pulling away the ribbon
- You may want to use tweezers to remove the gold ribbons as a more delicate and safe approach, but this is not required
- Do not pull away motherboard too hard as the ribbons are very fragile
Carefully remove the gold ribbons from the ports of the motherboard by lifting the gray tabs and pulling away the ribbon
You may want to use tweezers to remove the gold ribbons as a more delicate and safe approach, but this is not required
Do not pull away motherboard too hard as the ribbons are very fragile
Step 15
- Remove the SD card holder. It should easily come out because all of the prerequisite screws were already removed.
Remove the SD card holder. It should easily come out because all of the prerequisite screws were already removed.
Step 16
SD Motherboard
- Carefully remove the last gold ribbon by lifting the gray tab and sliding out the ribbon.
- Be sure to use extreme caution because if this ribbon breaks, you will need to buy a new camera.
Carefully remove the last gold ribbon by lifting the gray tab and sliding out the ribbon.
Be sure to use extreme caution because if this ribbon breaks, you will need to buy a new camera.
Step 17
- Viola! The motherboard is now removed and can be replaced with a new one.
Viola! The motherboard is now removed and can be replaced with a new one.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 5 other contributors
Isaiah De Leon
Member since: 01/29/2017
397 Reputation
3 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team 21-1, Maness Winter 2017
Member of Cal Poly, Team 21-1, Maness Winter 2017
CPSU-MANESS-W17S21G1
5 Members
10 Guides authored