Difficulty
Moderate
Steps
12
Time Required
15 minutes
Sections
1
- Lens Assembly
- 12 steps
Flags
0
BackSony Cyber-shot DSC-WX350
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lens Assembly
- Use the J00 screwdriver to take out the four 3mm black screws on the bottom and both sides of the camera.
Use the J00 screwdriver to take out the four 3mm black screws on the bottom and both sides of the camera.
1024
Step 2
- On the bottom of the camera slide the button over to open the battery case. Inside the battery opening use the J00 screwdriver to take out the single 3mm black screw.
On the bottom of the camera slide the button over to open the battery case. Inside the battery opening use the J00 screwdriver to take out the single 3mm black screw.
Step 3
- Use the J00 screwdriver to take out the single 3mm black screw on the left side of the camera .
Use the J00 screwdriver to take out the single 3mm black screw on the left side of the camera .
Step 4
- Use the plastic opening tool to pry open the back cover off.
Use the plastic opening tool to pry open the back cover off.
Step 5
- Use your fingers to slide out the controller wheel board ’s lower end, then unhook the other end.
Use your fingers to slide out the controller wheel board ’s lower end, then unhook the other end.
Step 6
- Take the LCD off by undoing the zif and sliding it out.
Take the LCD off by undoing the zif and sliding it out.
Step 7
- Once the LCD is off use the J00 screwdriver to take out the two 3mm silver screws. Once the screws are taken out pull off the piece with your fingers.
Once the LCD is off use the J00 screwdriver to take out the two 3mm silver screws. Once the screws are taken out pull off the piece with your fingers.
Step 8
- Now take out the 3 zifs by first opening the zif latch with your fingers and then sliding it out.
Now take out the 3 zifs by first opening the zif latch with your fingers and then sliding it out.
Step 9
- Carefully remove the lens assembly from the camera.
Carefully remove the lens assembly from the camera.
Step 10
- In order to access the CCD, loosen the 3 screws holding its metal lid.
- In order to access the lens mechanics, take out the 4 3mm screws on the edge of the lid, then the single 3 mm screw next to the motor.
In order to access the CCD, loosen the 3 screws holding its metal lid.
In order to access the lens mechanics, take out the 4 3mm screws on the edge of the lid, then the single 3 mm screw next to the motor.
Step 11
- Carefully tear off the ribbon glued to the plastic.
Carefully tear off the ribbon glued to the plastic.
Step 12
- Pull out the cogwheel with the drive unit.
- Now you can access the lens inner mechanics. You might wanna cover the CCD and the inner lens opening with tape to prevent dust from entering before you try to clean anything.
Pull out the cogwheel with the drive unit.
Now you can access the lens inner mechanics. You might wanna cover the CCD and the inner lens opening with tape to prevent dust from entering before you try to clean anything.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 5 other contributors
Joshua R Hammel
Member since: 05/22/2017
234 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
IUPUI, Team S1-G1, Wilson Summer 2017
Member of IUPUI, Team S1-G1, Wilson Summer 2017
IUPUI-WILSON-SU17S1G1
4 Members
3 Guides authored
Arno - May 4, 2019
Reply
Hi, I think on my sensor chip is some dust. Is it possible to clean that or is it one unit with lens? There is no picture about this detail….
Joshua O’Brien - Aug 19, 2022
Reply
Hi there, does anyone know who I could go to to fix the lens (replace them) on my Sony wx-350 camera Thank you!
