Sony Cyber Shot Dsc Wx100 Lcd Screen Replacement Repair Guide

Difficulty

Moderate

Steps

8

Time Required

                          20 minutes            

Sections

3

• Battery
• 2 steps
• Outer Casing
• 3 steps
• LCD Screen
• 3 steps

Flags

0

• BackSony Cyber-shot DSC-WX100

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Open the flap indicated to allow access to the battery slot.
• The gray switch indicated has to be moved to the right in order to release the flap.

Open the flap indicated to allow access to the battery slot.

The gray switch indicated has to be moved to the right in order to release the flap.

1024

Step 2

• If the old battery is still in the slot, then make sure the camera is turned off prior to removal.
• If there is a battery currently in the slot, remove by first pulling downwards on the blue component. This will allow you to remove the battery from the slot.

If the old battery is still in the slot, then make sure the camera is turned off prior to removal.

If there is a battery currently in the slot, remove by first pulling downwards on the blue component. This will allow you to remove the battery from the slot.

Step 3

              Outer Casing               

• Remove all of the 1mm screws using a Philips #000 Screwdriver.
• Remover the rest of the screws (2mm) from the camera covers using a Phillips #000 Screwdriver.

Remove all of the 1mm screws using a Philips #000 Screwdriver.

Remover the rest of the screws (2mm) from the camera covers using a Phillips #000 Screwdriver.

Step 4

• Use the plastic opening tool to gently remove the front and back plates of the camera.

Use the plastic opening tool to gently remove the front and back plates of the camera.

Step 5

• Use a plastic opening tool to gently release the two indicated tabs.

Use a plastic opening tool to gently release the two indicated tabs.

Step 6

              LCD Screen               

• Pull up on the lower end of the plate. Lift it so the plate is high enough so that the marked bump is not holding it in place.
• Pull away from the camera at the end of the metal plate with the blue circuits to then remove the plate from the rest of the camera.
• For help please watch the video.

Pull up on the lower end of the plate. Lift it so the plate is high enough so that the marked bump is not holding it in place.

Pull away from the camera at the end of the metal plate with the blue circuits to then remove the plate from the rest of the camera.

For help please watch the video.

Step 7

• Remove this screw (1mm) with a Phillips #000 Screwdriver.
• Gently lift the LCD from the metal plate.
• Remove the metal plate that was underneath the LCD screen from the camera.

Remove this screw (1mm) with a Phillips #000 Screwdriver.

Gently lift the LCD from the metal plate.

Remove the metal plate that was underneath the LCD screen from the camera.

Step 8

• Use the plastic opening tool to pry the black bar upwards.
• Pull the LCD screen from out of the slot.

Use the plastic opening tool to pry the black bar upwards.

Pull the LCD screen from out of the slot.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    Peter Prins                     

Member since: 03/19/2015

262 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       Michigan Tech, Team 1-9, Lauer Spring 2015                        

                                                  Member of Michigan Tech, Team 1-9, Lauer Spring 2015 



                    MTU-LAUER-S15S1G9                     


                                            2 Members                     


                                            6 Guides authored                     

k.bilius - Mar 26, 2018

Reply

be careful with capacitor !!! i touched it 5-10 minutes after battery was removed and felt electricity in my chest, ears… be careful :D